Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Automate Solaris x86 Jumpstart
Operating Systems Solaris Automate Solaris x86 Jumpstart Post 302330865 by reborg on Thursday 2nd of July 2009 02:58:31 PM
Old 07-02-2009
racbern, I happen to know exactly what you are doing here.

DN2, this is post install, there are some application parameters and sizing questions that have to be answered after the first boot.

You can do exactly the same as on Sparc, the only difference is that you need to update the grub kernel boot like to add "-B console=ttya" to the kernel line, then you get the console on the text based ILOM and you can continue to answering the configuration questions.

The easiest way to get this working is to do the first run using autoexpect and then edit the generated script.
 

9 More Discussions You Might Find Interesting

1. Solaris

Jumpstart on x86 client- prompt for CD2

Hi I just configured a jumpstart server for x86 and sparc clients. I don't use a dhcp server, so I configured /etc/ethers and did add_install_client to update /etc/bootparams. The sparc installation ist working, but the x86 installation stops after CD1 was successfully installed. What I did: I... (2 Replies)
Discussion started by: Jay_Fisi
2 Replies

2. Solaris

Jumpstart Solaris 10 x86

I need a little help figuring out why my custom jumpstart network installation is dumping me to a manual install. I am trying to install Solaris 10 (unattended) over the wire from my jumpstart server to an HP Proliant DL380 server but I'm having difficulties with the unattended part. So, what... (2 Replies)
Discussion started by: alias.256
2 Replies

3. Solaris

Solaris 10 x86 Jumpstart w/o GUI

Does anyone know how to Jumpstart a Solaris 10 x86 system without the GUI? I would like to keep the Jumpstart and/or Flash Archive install in a console text mode if possible but I've not had much luck finding instructions. I'm guessing this is going to be accomplished from the grub menu with a... (5 Replies)
Discussion started by: alias.256
5 Replies

4. Solaris

One time network boot of Jumpstart x86 client

I am trying to find an approach that has been effective for automating the installation of Solaris 10 x86 using Jumpstart technology. I have configured an Jumpstart server and a Solaris dhcp server with appropriate macros for passing the client information about its boot environment. The problem is... (7 Replies)
Discussion started by: chajo19
7 Replies

5. Solaris

Jumpstart sparc client using x86 server.

Can I use a Jumpstart enviroment on x86 to install a sparc64 client? The idea is to install Solaris in an virtual environment (Sun Virtual Box) running on a pc (AMD), configure a Jumpstart server, and have a SUN Ultra 60 (sparc64) installed via the Jumpstart server. The SUN has no cdrom... (4 Replies)
Discussion started by: eldiablo
4 Replies

6. Solaris

Jumpstart Installation from X86 machine

Hi friends , i have on ultra 10 Sparc machine . Due to some problem my OS is fully corrupted , so i am planning to install again but my problem is the cd drive in Ultra 10 machine is not working. Now i am planning to use Jumpstart installation method to install my server. But i... (4 Replies)
Discussion started by: vr_mari
4 Replies

7. Solaris

custom jumpstart on x86 with DHCP/PXE goes into interactive mode

client boots fine, it gets the ip 192.168.0.10 and the bootfile. Then there is : SunOS 5.10 Version Generic_141445-09 32-bit" ... Configuring devices. Custom JumpStart Reading ZFS config: done Setting up Java. Please wait ... NOTE: Not enough memory for graphical installation. Graphical... (4 Replies)
Discussion started by: TomSu
4 Replies

8. Solaris

Solaris x86 installation using jumpstart does not local boot ( boot from hdd)

I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies

9. Solaris

Installing Solaris x86 using jumpstart does not set the hostname for the target

Installing Solaris x86 using jumpstart does not set the hostname for the target. Any idea where do we need to specify hostname to be set for jumpstart installation. (1 Reply)
Discussion started by: hemalsid
1 Replies

LEARN ABOUT CENTOS

grub2-bios-setup

GRUB-BIOS-SETUP(3)					     Library Functions Manual						GRUB-BIOS-SETUP(3)

NAME

       grub-bios-setup -- Set up images to boot from a device.

SYNOPSIS

       grub-bios-setup [-a | --allow-floppy] [-b | --boot-image=FILE]
			[-c | --core-image=FILE] [-d | --directory=DIR]
			[-f | --force] [-m | --device-map=FILE]
			[-s | --skip-fs-probe] [-v | --verbose] DEVICE

DESCRIPTION

       You should not normally run this program directly.  Use grub-install instead.

OPTIONS

       --allow-floppy
	      Make  the device also bootable as a floppy.  This option is the default for /dev/fdX devices.  Some BIOSes will not boot images cre-
	      ated with this option.

       --boot-image=FILE
	      Use FILE as the boot image.  The default value is boot.img.

       --core-image=FILE
	      Use FILE as ther core image.  The default value is core.img.

       --directory=DIR
	      Use GRUB files in the directory DIR.  The default value is /boot/grub.

       --force
	      Install even if problems are detected.

       --device-map=FILE
	      Use FILE as the device map.  The default value is /boot/grub/device.map .

       --skip-fs-probe
	      Do not probe DEVICE for filesystems.

       --verbose
	      Print verbose messages.

SEE ALSO

       info grub

								  Wed Feb 26 2014						GRUB-BIOS-SETUP(3)
All times are GMT -4. The time now is 09:55 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy