07-02-2009
Quote:
Originally Posted by
sysgate
Hello, I hope it's not too late. I thought I was going to go deeply into the network layers, and so on, but as always, wikipedia has better words than me and my poor English. Please read
this short article and let us know if this is insufficient.
Hi sysgate,
thanks for the link.
However, it only mentioned to do it on the route.
What about my case which happened to be a server?
Thanks in advance.
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I have a machine that sits on 10.2 network.
I need to ssh from this to another box that is on both 10.125 & 10.140 VLANs
what should I need to do?
Thanks! (3 Replies)
Discussion started by: chaandana
3 Replies
2. HP-UX
I want to make static route how would I proceed?
I'm using "route add DestinationIP gatewayIP hop to 1
I would like to make this permanent, so when it reboots I don't want to loose it, would I do this in netconf file? If so where?
I did a search got this site, it didn't help much. ... (2 Replies)
Discussion started by: catwomen
2 Replies
3. UNIX for Dummies Questions & Answers
Hi,
Request you to please tell me the command or the process to add the static route in redhat linux.
Thanks in Advance.
Regards
Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies
4. Red Hat
I have a machine with an interface that has two different addresses on CentOS 5
eth0: 10.20.21.77
eth0:1 141.218.1.221
If I issue this command I get the result I'm looking for.
/sbin/route add -net 141.218.1.0 netmask 255.255.255.0 gw 10.20.21.77
ip route show dev eth0
141.218.1.0/24... (1 Reply)
Discussion started by: beaker457
1 Replies
5. AIX
#netstat -nr (shows the following with more static routes)
192.168.18.202 10.129.155.1 UGH 0 29 en0 - -
and i just want to remove the above one
i tried
#smitty rmroute
destination type= net
dest add = 192.168.18.202
default gateway= 10.129.155.1
net... (1 Reply)
Discussion started by: pchangba1
1 Replies
6. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
7. Solaris
Hi all
i have a simple question here
I'm kind of newbie on solaris development
currently i'm trying to add static route to solaris environment
and i got error, each time i add this static route to it
btw this is my command :
root@xxxxxx # ping 1.2.3.1
1.2.3.1 is alive
echo ... (15 Replies)
Discussion started by: l33tbot_if
15 Replies
8. AIX
Anyone know how to edit a static route in AIX? I find myself deleting and then recreating the route with the new information. Would be nice to know how to edit the route. (3 Replies)
Discussion started by: bbbngowc
3 Replies
9. Red Hat
Hello Guys..
I am facing this weird problem of static route not added after reboot!!
Following is my route-<interface> file..
# cat /etc/sysconfig/network-scripts/route-eth0
ADDRESS0=172.31.0.1
NETMASK0=255.255.255.255
GATEWAY0=192.168.208.1
ADDRESS1=172.31.15.2... (3 Replies)
Discussion started by: parth_buch
3 Replies
10. IP Networking
Hi all,
This may be the basic question of Routing but I am a sort of new to networking so I am asking.
Do I need to put route for my router's LAN port ip to WAN (serial) port ip Or the router itself can communicate between its ports without routes.
lan (172.26.40.5) ... (3 Replies)
Discussion started by: dextergenious
3 Replies
route(8c) route(8c)
Name
route - manually manipulate the routing tables
Syntax
/etc/route [ -f ] [ -n ] command args ]
Description
The program is used to manipulate the network routing tables manually. However, normally it is not needed, as the system routing table
management daemon, should tend to this task.
The program accepts two commands: add, to add a route and delete, to delete a route.
All commands have the following syntax:
/etc/route command [ net | host ] destination gateway [ metric ]
In this syntax, destination is a host or network for which the route is to, gateway is the gateway to which packets should be addressed,
and metric is an optional count indicating the number of hops to the destination. The metric is required for add commands. It must be
zero if the destination is on a directly-attached network, and nonzero if the route utilizes one or more gateways.
When adding a route with metric 0, the gateway given is the address of this host on the common network, indicating the interface to be used
for transmission. Routes to a particular host are distinguished from routes to a network by interpreting the Internet address associated
with destination. The optional keywords net and host force the destination to be interpreted as a network or host, respectively. If the
destination has a local address part of INADDR_ANY, then the route is assumed to be to a network. Otherwise, it is presumed to be a route
to a host. If the route is to a destination connected via a gateway, the metric should be greater than 0. All symbolic names specified
for a destination or gateway are looked up first as a host name using If this lookup fails, is then used to interpret the name as that of a
network.
The command uses a raw socket and the SIOCADDRT and SIOCDELRT ioctls to do its work. As such, only the superuser can modify the routing
tables.
Options
-f Flushes the routing tables of all gateway entries. If is used with one of the commands described above, the tables are flushed prior
to the command's application.
-n Prevents attempts to print host and network names symbolically when reporting actions.
Restrictions
The change operation is not implemented. Therefore, you should first add the new route, and then delete the old one.
Diagnostics
add [host | network] %s: gateway %s flags %x"
The specified route is being added to the tables. The values printed are from the routing table entry supplied in the ioctl call. If the
gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically as
well as symbolically.
delete [ host | network] %s: gateway %s flags %x
The specified route is being deleted from the tables. The values printed are from the routing table entry supplied in the ioctl call. If
the gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically
as well as symbolically.
%s %s done
When the flag is specified, each routing table entry that is deleted is indicated with a message of this form.
Network is unreachable
An attempt to add a route failed because the gateway listed was not on a directly-connected network. The next-hop gateway must be given.
not in table
A delete operation was attempted for an entry which was not present in the tables.
routing table overflow
An add operation was attempted, but the system was low on resources and was unable to allocate memory to create the new entry.
See Also
intro(4n), routed(8c)
route(8c)