the mac comes from the hardware itself! why do you need to change this? if you need to change them, a little bit of google might have you lead to something like this
Hi sir,
i want to make such programe which takes MAC(Ethernet) address of any host & give me its IP address.......
but i'm nt getting that how i can pass the MAC address to Frame........
Please give me an idea for making such program...
Thanks & regards
Krishna (3 Replies)
Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.
would some one help me out in this.
Thanks
Gopi (1 Reply)
Dear Friends ,
I am using RHEL 5 . In my Linux Box i have two Lan cards (eth0 and eth1) .
"eth0" is connected with network 192.168.10.0 and "eth1" is connected with network 192.168.11.0 . Both Network are inter connected via routing .
Now I want a situation where , I want to dedicatedly... (2 Replies)
hi,
how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc.. (2 Replies)
Hi there
I lost connectivity to one of our remote systems and when I checked the messages log I found the following:
Aug 10 23:42:34 host xntpd: time reset (step) 1.681729 s
Aug 16 13:20:51 host ip: WARNING: node "mac address" is using our IP address x.x.x.x on aggr1
Aug 16 13:20:51 host... (9 Replies)
I have 2 physical interfaces (bnx0 and bnx1) aggregated into aggr1. I need to assign second IP, and normally I know how to do it to physical interface (i.e. bnx0:1) however same trick (aggr1:1) is not working. Is there any way to do it? (0 Replies)
Hi folks,
I found out the following:
provadm@BKP_LIV_NPPGW_02:home/provadm%/usr/sbin/arp -a
Net to Media Table: IPv4
Device IP Address Mask Flags Phys Addr
------ -------------------- --------------- -------- --------------------
ce5 BKP_OnM_NPPGW_02 255.255.255.255 SPLA 00:14:4f:44:e0:86... (1 Reply)
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
four interfaces with ifconfig
all interfaces have the same mac. If is not set for unique.
but it still works.
what difference does it make to have all macs the same or different? (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT DEBIAN
install-solaris
install-solaris(1M)install-solaris(1M)NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)