07-01-2009
How to assign MAC address to N/W interface in solaris
I m having interface ce0 ce1 and its sub interfaces for that.
I want to give MAC addresses for the same.
How will I assign it.
Please give solution for the same
Last edited by sunray; 07-01-2009 at 08:20 AM..
10 More Discussions You Might Find Interesting
1. IP Networking
Hi sir,
i want to make such programe which takes MAC(Ethernet) address of any host & give me its IP address.......
but i'm nt getting that how i can pass the MAC address to Frame........
Please give me an idea for making such program...
Thanks & regards
Krishna (3 Replies)
Discussion started by: krishnacins
3 Replies
2. IP Networking
Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.
would some one help me out in this.
Thanks
Gopi (1 Reply)
Discussion started by: Gopi Krishna P
1 Replies
3. Red Hat
Dear Friends ,
I am using RHEL 5 . In my Linux Box i have two Lan cards (eth0 and eth1) .
"eth0" is connected with network 192.168.10.0 and "eth1" is connected with network 192.168.11.0 . Both Network are inter connected via routing .
Now I want a situation where , I want to dedicatedly... (2 Replies)
Discussion started by: shipon_97
2 Replies
4. Solaris
hi,
how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc.. (2 Replies)
Discussion started by: pankajd
2 Replies
5. IP Networking
Hi there
I lost connectivity to one of our remote systems and when I checked the messages log I found the following:
Aug 10 23:42:34 host xntpd: time reset (step) 1.681729 s
Aug 16 13:20:51 host ip: WARNING: node "mac address" is using our IP address x.x.x.x on aggr1
Aug 16 13:20:51 host... (9 Replies)
Discussion started by: notreallyhere
9 Replies
6. UNIX for Dummies Questions & Answers
I have 2 physical interfaces (bnx0 and bnx1) aggregated into aggr1. I need to assign second IP, and normally I know how to do it to physical interface (i.e. bnx0:1) however same trick (aggr1:1) is not working. Is there any way to do it? (0 Replies)
Discussion started by: bratan
0 Replies
7. Solaris
Hi folks,
I found out the following:
provadm@BKP_LIV_NPPGW_02:home/provadm%/usr/sbin/arp -a
Net to Media Table: IPv4
Device IP Address Mask Flags Phys Addr
------ -------------------- --------------- -------- --------------------
ce5 BKP_OnM_NPPGW_02 255.255.255.255 SPLA 00:14:4f:44:e0:86... (1 Reply)
Discussion started by: kimurayuki
1 Replies
8. IP Networking
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies
9. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
10. IP Networking
four interfaces with ifconfig
all interfaces have the same mac. If is not set for unique.
but it still works.
what difference does it make to have all macs the same or different? (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT DEBIAN
shorewall-maclist
SHOREWALL-MACLIST(5) [FIXME: manual] SHOREWALL-MACLIST(5)
NAME
maclist - Shorewall MAC Verification file
SYNOPSIS
/etc/shorewall/maclist
DESCRIPTION
This file is used to define the MAC addresses and optionally their associated IP addresses to be allowed to use the specified interface.
The feature is enabled by using the maclist option in the shorewall-interfaces[1](5) or shorewall-hosts[2](5) configuration file.
The columns in the file are as follows (where the column name is followed by a different name in parentheses, the different name is used in
the alternate specification syntax).
DISPOSITION - {ACCEPT|DROP|REJECT}[:log-level]
ACCEPT or DROP (if MACLIST_TABLE=filter in shorewall.conf[3](5), then REJECT is also allowed). If specified, the log-level causes
packets matching the rule to be logged at that level.
INTERFACE - interface
Network interface to a host.
MAC - address
MAC address of the host -- you do not need to use the Shorewall format for MAC addresses here. If IP ADDRESSESES is supplied then MAC
can be supplied as a dash (-)
IP ADDRESSES (addresses) - [address[,address]...]
Optional - if specified, both the MAC and IP address must match. This column can contain a comma-separated list of host and/or subnet
addresses. If your kernel and iptables have iprange match support then IP address ranges are also allowed. Similarly, if your kernel
and iptables include ipset support than set names (prefixed by "+") are also allowed.
FILES
/etc/shorewall/maclist
SEE ALSO
http://shorewall.net/MAC_Validation.html
http://shorewall.net/configuration_file_basics.htm#Pairs
shorewall(8), shorewall-accounting(5), shorewall-actions(5), shorewall-blacklist(5), shorewall-hosts(5), shorewall_interfaces(5),
shorewall-ipsets(5), shorewall-masq(5), shorewall-nat(5), shorewall-netmap(5), shorewall-params(5), shorewall-policy(5),
shorewall-providers(5), shorewall-proxyarp(5), shorewall-rtrules(5), shorewall-routestopped(5), shorewall-rules(5), shorewall.conf(5),
shorewall-secmarks(5), shorewall-tcclasses(5), shorewall-tcdevices(5), shorewall-tcrules(5), shorewall-tos(5), shorewall-tunnels(5),
shorewall-zones(5)
NOTES
1. shorewall-interfaces
http://www.shorewall.net/manpages/shorewall-interfaces.html
2. shorewall-hosts
http://www.shorewall.net/manpages/shorewall-hosts.html
3. shorewall.conf
http://www.shorewall.net/manpages/shorewall.conf.html
[FIXME: source] 06/28/2012 SHOREWALL-MACLIST(5)