07-01-2009
How to assign MAC address to N/W interface in solaris
I m having interface ce0 ce1 and its sub interfaces for that.
I want to give MAC addresses for the same.
How will I assign it.
Please give solution for the same
Last edited by sunray; 07-01-2009 at 08:20 AM..
10 More Discussions You Might Find Interesting
1. IP Networking
Hi sir,
i want to make such programe which takes MAC(Ethernet) address of any host & give me its IP address.......
but i'm nt getting that how i can pass the MAC address to Frame........
Please give me an idea for making such program...
Thanks & regards
Krishna (3 Replies)
Discussion started by: krishnacins
3 Replies
2. IP Networking
Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.
would some one help me out in this.
Thanks
Gopi (1 Reply)
Discussion started by: Gopi Krishna P
1 Replies
3. Red Hat
Dear Friends ,
I am using RHEL 5 . In my Linux Box i have two Lan cards (eth0 and eth1) .
"eth0" is connected with network 192.168.10.0 and "eth1" is connected with network 192.168.11.0 . Both Network are inter connected via routing .
Now I want a situation where , I want to dedicatedly... (2 Replies)
Discussion started by: shipon_97
2 Replies
4. Solaris
hi,
how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc.. (2 Replies)
Discussion started by: pankajd
2 Replies
5. IP Networking
Hi there
I lost connectivity to one of our remote systems and when I checked the messages log I found the following:
Aug 10 23:42:34 host xntpd: time reset (step) 1.681729 s
Aug 16 13:20:51 host ip: WARNING: node "mac address" is using our IP address x.x.x.x on aggr1
Aug 16 13:20:51 host... (9 Replies)
Discussion started by: notreallyhere
9 Replies
6. UNIX for Dummies Questions & Answers
I have 2 physical interfaces (bnx0 and bnx1) aggregated into aggr1. I need to assign second IP, and normally I know how to do it to physical interface (i.e. bnx0:1) however same trick (aggr1:1) is not working. Is there any way to do it? (0 Replies)
Discussion started by: bratan
0 Replies
7. Solaris
Hi folks,
I found out the following:
provadm@BKP_LIV_NPPGW_02:home/provadm%/usr/sbin/arp -a
Net to Media Table: IPv4
Device IP Address Mask Flags Phys Addr
------ -------------------- --------------- -------- --------------------
ce5 BKP_OnM_NPPGW_02 255.255.255.255 SPLA 00:14:4f:44:e0:86... (1 Reply)
Discussion started by: kimurayuki
1 Replies
8. IP Networking
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies
9. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
10. IP Networking
four interfaces with ifconfig
all interfaces have the same mac. If is not set for unique.
but it still works.
what difference does it make to have all macs the same or different? (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT CENTOS
nameif
NAMEIF(8) Linux System Administrator's Manual NAMEIF(8)
NAME
nameif - name network interfaces based on MAC addresses
SYNOPSIS
nameif [-c configfile] [-s]
nameif [-c configfile] [-s] {interface macaddress}
NOTE
This program is obsolete. For replacement check ip link. This functionality is also much better provided by udev methods.
DESCRIPTION
nameif renames network interfaces based on mac addresses. When no arguments are given /etc/mactab is read. Each line of it contains an
interface name and a Ethernet MAC address. Comments are allowed starting with #. Otherwise the interfaces specified on the command line
are processed. nameif looks for the interface with the given MAC address and renames it to the name given.
When the -s argument is given all error messages go to the syslog.
When the -c argument is given with a file name that file is read instead of /etc/mactab.
NOTES
nameif should be run before the interface is up, otherwise it'll fail.
FILES
/etc/mactab
SEE ALSO
ip(8), udev(7)
BUGS
Only works for Ethernet currently.
net-tools 2008-10-03 NAMEIF(8)