Hi,
How do i know if the files are transferred succesfully when i use SCP to transfer files between 2 servers.
One more is i am trying to send all the files in a single shot by using * to save the connection time. So can i know when the scp breakes in the middle
scp $sourcepath/*... (9 Replies)
Hi Frdz
I have a problem like.
I need to transfer a file from source to destination (different systems with different IPs) using "scp" command and before transfer the file i have to check the file is available in destination or not, if it is there no need to transfer, otherwise we have to... (5 Replies)
FILE_LIST="{a.txt,b.txt,cal*}"
scp -r $..$REMOTE_PATH$FILE_LIST $LOCAL_PATH
This script passes only when all the three files are transfere, wat if only two file are transfered, but still I was to make the return code as pass.
is it possible. (2 Replies)
I am not able to throw a file from server173 to server067
i.e.
wlsuser@server173> scp /tmp/harsha.txt wlsuser@server067:/tmp
fails
However, I am able to pull a file from server173 onto server067's /tmp dir
wlsuser@server067> scp wlsuser@server173:/tmp/harsha.txt /tmp... (2 Replies)
Whenever I transfer file through SCP between two server it gives below given message.....Is there a way to avoid it....
Target server : newyork
$ scp ABC27801.iue newyork:./iABC/x0017801.iue
Message
=====
This system is for the use of authorized users only. Individuals using this... (1 Reply)
I have 3 AIX server namely - Server 1 , Server 2 and Server 3.
And have done SCP setup between Server 1 and Server 2 so that i dont have to give password when i transfer file from Server 1 to Server 2 by setting public key between the server.
Q1. If the unix password of the target server... (3 Replies)
On unix AIX server, when I am trying to transfer file from one directory to another directory on the same server through a program(where i call the script) it gives error "Lost Connection". (5 Replies)
I am testing the following command to transfer a file from my server (AIX 5.2) to another server. I was able to generate the keys and sent them the public key.
scp -v -P 4030 /home/lawson/.ssh/jimtest.txt someuser@some.ftpsite.net:/Inbound/jimtest.txt > jimtest_out.txt 2>&1
Based on... (3 Replies)
I am trying to transfer a zip file of around 30 MB in my automation script using scp from system A to B.
When I manually do scp, file is complete transferred but when automation shell script runs it, zip file is not completely transferred.
Stack Trace while doing manual :
Executing:... (1 Reply)
Discussion started by: Shaishav Shah
1 Replies
LEARN ABOUT DEBIAN
innxbatch
INNXBATCH(8) System Manager's Manual INNXBATCH(8)NAME
innxbatch - send xbatched Usenet articles to a remote NNTP server
SYNOPSIS
innxbatch [ -D ] [ -t timeout ] [ -T timeout ] [ -v ] host file ...
DESCRIPTION
Innxbatch connects to the NNTP server at the specified host and sends it the specified xbatch files, using the XBATCH extension to the NNTP
protocol. It is normally invoked by a script run out of cron(8) that uses shlock(1) to lock the host name, followed by a ctlinnd(8) command
to flush the batchfile.
Innxbatch normally blocks until the connection is made. To specify a timeout on how long to try to make the connection, use the ``-t''
flag.
To specify the total amount of time that should be allowed for article transfers, use the ``-T'' flag.
The default is to wait until an I/O error occurs, or all the articles have been transferred. If the ``-T'' flag is used, the time is
checked just before an article is started; it will not abort a transfer that is in progress. Both values are measured in seconds.
Each fileis removed after it has been successfully transferred.
If a communication error such as a write(2) failure, or an unexpected reply from the remote server occurs, innxbatch will stop sending and
leave all remaining files untouched for later retry.
Upon exit, innxbatch reports transfer and CPU usage statistics via syslog(3). If the ``-v'' flag is used, they will also be printed on the
standard output.
Use the ``-D'' flag to print debugging information on standard error. This will show the protocol transactions between innxbatch and the
NNTP server on the remote host.
A sample newsfeeds(5) entry to produce appropriate xbatch files (thanks to Karsten Leipold <poldi@dfn.de>):
nase
:*
:Tc,Wnb
:/usr/lib/news/bin/batcher
-p "(/bin/gzip > /var/spool/news/out.going/nase.$$)"
nase.do.main
A sample script to invoke innxbatch(8) is:
#!/bin/sh
## SH script to send xbatches for a site, wrapped around innxbatch
## Invocation:
## sendxbatches.sh <sitename> <hostname> <xbatch file name> ...
if [ $# -le 3 ]
then
echo "usage: $0 <sitename> <hostname> <xbatch file name>"
exit 1
fi
## =()< . @<_PATH_SHELLVARS>@>()=
. /usr/lib/news/innshellvars
site="$1"; host="$2"; shift; shift
ctlinnd flush "$site"
&& sleep 5
&& exec $NEWSBIN/innxbatch -v -D "$host" $*
HISTORY
Written by Stefan Petri <petri@ibr.cs.tu-bs.de>, modelled after innxmit(8) and the XBATCH patch for the nntp reference implementation.
SEE ALSO innxmit(8), nntpsend(8), ctlinnd(8), innd(8), newsfeeds(5), shlock(1).
INNXBATCH(8)