06-29-2009
Hello, I hope it's not too late. I thought I was going to go deeply into the network layers, and so on, but as always, wikipedia has better words than me and my poor English. Please read
this short article and let us know if this is insufficient.
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I have a machine that sits on 10.2 network.
I need to ssh from this to another box that is on both 10.125 & 10.140 VLANs
what should I need to do?
Thanks! (3 Replies)
Discussion started by: chaandana
3 Replies
2. HP-UX
I want to make static route how would I proceed?
I'm using "route add DestinationIP gatewayIP hop to 1
I would like to make this permanent, so when it reboots I don't want to loose it, would I do this in netconf file? If so where?
I did a search got this site, it didn't help much. ... (2 Replies)
Discussion started by: catwomen
2 Replies
3. UNIX for Dummies Questions & Answers
Hi,
Request you to please tell me the command or the process to add the static route in redhat linux.
Thanks in Advance.
Regards
Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies
4. Red Hat
I have a machine with an interface that has two different addresses on CentOS 5
eth0: 10.20.21.77
eth0:1 141.218.1.221
If I issue this command I get the result I'm looking for.
/sbin/route add -net 141.218.1.0 netmask 255.255.255.0 gw 10.20.21.77
ip route show dev eth0
141.218.1.0/24... (1 Reply)
Discussion started by: beaker457
1 Replies
5. AIX
#netstat -nr (shows the following with more static routes)
192.168.18.202 10.129.155.1 UGH 0 29 en0 - -
and i just want to remove the above one
i tried
#smitty rmroute
destination type= net
dest add = 192.168.18.202
default gateway= 10.129.155.1
net... (1 Reply)
Discussion started by: pchangba1
1 Replies
6. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
7. Solaris
Hi all
i have a simple question here
I'm kind of newbie on solaris development
currently i'm trying to add static route to solaris environment
and i got error, each time i add this static route to it
btw this is my command :
root@xxxxxx # ping 1.2.3.1
1.2.3.1 is alive
echo ... (15 Replies)
Discussion started by: l33tbot_if
15 Replies
8. AIX
Anyone know how to edit a static route in AIX? I find myself deleting and then recreating the route with the new information. Would be nice to know how to edit the route. (3 Replies)
Discussion started by: bbbngowc
3 Replies
9. Red Hat
Hello Guys..
I am facing this weird problem of static route not added after reboot!!
Following is my route-<interface> file..
# cat /etc/sysconfig/network-scripts/route-eth0
ADDRESS0=172.31.0.1
NETMASK0=255.255.255.255
GATEWAY0=192.168.208.1
ADDRESS1=172.31.15.2... (3 Replies)
Discussion started by: parth_buch
3 Replies
10. IP Networking
Hi all,
This may be the basic question of Routing but I am a sort of new to networking so I am asking.
Do I need to put route for my router's LAN port ip to WAN (serial) port ip Or the router itself can communicate between its ports without routes.
lan (172.26.40.5) ... (3 Replies)
Discussion started by: dextergenious
3 Replies
LEARN ABOUT DEBIAN
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)