06-27-2009
Quote:
Originally Posted by
System Shock
The right test woulb be to configure a laptop with the IP of the server and plug it right to the very same cable that plugs into the server.
Hello... this is exactly what Im referring to.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies
2. UNIX for Advanced & Expert Users
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?
Thanx :)
-Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies
3. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
4. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
5. Solaris
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies
6. Solaris
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies
7. Solaris
Hi All,
1. modify /etc/default/login file as
make commented # console=
2.put my laptops ip at both
/etc/inet/ipnodes and /etc/host file
still i can login via telnet/ftp through a DB9-serial cable, but when i tried
through a lan stratight cable directly connected that machine... (7 Replies)
Discussion started by: mahadib
7 Replies
8. Solaris
Hi all,
really interesting thing I have encountered . So :
root@host4 # uname -a
SunOS host4 5.9 Generic_122300-31 sun4u sparc SUNW,Sun-Fire-880
root@host4 # scinstall -p
3.2
latest recommended patches applied ..all SUN cluster patches applied.
SUN cluster software installed without... (2 Replies)
Discussion started by: samar
2 Replies
9. Solaris
We are unable to ping from Sun Ultra 60 to Ultra 10 machine and vice versa. We are getting an error message Cable Link Down ?. It was working fine.
Troubleshooting steps taken.
1) Changed the IPaddresses on both machines 192.168.10.10 and 192.168.10.20. These machines connected through 8 port... (2 Replies)
Discussion started by: vijaykrishna
2 Replies
10. Red Hat
I am facing strange problem regarding hostname on my Linux(2.6.18-164.el5xen x86_64 GNU/Linux), the hostname changes if reboot with lan cable and with NO lan cable
Reboot with lan cable:
The hostname is ubunut
Unable to connect Oracle database using sqlplus some times database is not... (2 Replies)
Discussion started by: LinuxLearner
2 Replies
vpcd(8) powerman vpcd(8)
NAME
vpcd - virtual power control daemon
SYNOPSIS
vpcd [--port PORT]
DESCRIPTION
vpcd is a test program for PowerMan which emulates a remote power control device. It can be run interactively by the powerman daemon, or
it can listen on a port of your choosing.
OPTIONS
-p, --port PORT
Instructs vpcd to listen for connections on the specified port instead of using stdin/stdout. Only one connection will be accepted.
INTERACTIVE COMMANDS
The following commands are available at the vpcd> prompt:
login The login command must br run before any of the other commands will work. No username or password is required.
logoff Return vpcd to the initial state.
stat PLUG|*
Show the power status of PLUG. If PLUG is ``*'', perform this action on all plugs.
beacon PLUG|*
Show the beacon status of PLUG. If PLUG is ``*'', perform this action on all plugs.
temp PLUG|*
Show the temperature of the node attached to PLUG. If PLUG is ``*'', perform this action on all plugs.
spew COUNT
Print COUNT 80-char lines. This is the basis of a buffer handling test.
on PLUG|*
Turn on PLUG. If PLUG is ``*'', perform this action on all plugs.
off PLUG|*
Turn off PLUG. If PLUG is ``*'', perform this action on all plugs.
flash PLUG|*
Light the beacon on PLUG. If PLUG is ``*'', perform this action on all plugs.
unflash PLUG|*
Unlight the beacon on PLUG. If PLUG is ``*'', perform this action on all plugs.
reset PLUG|*
Reset the node attached to PLUG. If PLUG is ``*'', perform this action on all plugs.
FILES
/usr/sbin/vpcd
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 vpcd(8)