Sponsored Content
Operating Systems Solaris SUNW, hme0: Link Down - Cable problem Post 302329281 by System Shock on Friday 26th of June 2009 12:07:11 PM
Old 06-26-2009
Quote:
Originally Posted by incredible
Do one simple test. ensure that the IP on your system is plumbed up and is "UP". configure your laptop to an IP of the same subnet and see if you can ping. This will tell your if your Nic is good or not
That's incorrect. If you configure a laptop on the same subnet and try to ping the server, that ping still has to go through the laptop's NIC, the cable to the patch panel, the switch port the patch panel is connected to, the other switch port, the other patch panel, the cable from the patch panel to the server, then the server NIC. IF you ping doesn't go through, where's the problem? It could be any of the points mentioned above.

The right test woulb be to configure a laptop with the IP of the server and plug it right to the very same cable that plugs into the server.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

hme0 babble -- ?

Dear Reader, I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages. The message is hme0: babble.. The port is up and alive. What does this message mean.. Is the on board port is about to fail?? Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies

2. UNIX for Advanced & Expert Users

Hme0 interfaces...

How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this? Thanx :) -Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies

3. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created... (1 Reply)
Discussion started by: fnoyan
1 Replies

4. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks (2 Replies)
Discussion started by: waterbear
2 Replies

5. Solaris

hme0 problem after reboot

Hi ..... My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command after reboot : # ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies

6. Solaris

sun 420r hme0 not responding

I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network. If I ping 127.0.0.1 it says alive. Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies

7. Solaris

cannot telnet/ftp to solaris machine by straight cable makes problem ..

Hi All, 1. modify /etc/default/login file as make commented # console= 2.put my laptops ip at both /etc/inet/ipnodes and /etc/host file still i can login via telnet/ftp through a DB9-serial cable, but when i tried through a lan stratight cable directly connected that machine... (7 Replies)
Discussion started by: mahadib
7 Replies

8. Solaris

what is going on with SUNW.HAStoragePlus?!!!!!

Hi all, really interesting thing I have encountered . So : root@host4 # uname -a SunOS host4 5.9 Generic_122300-31 sun4u sparc SUNW,Sun-Fire-880 root@host4 # scinstall -p 3.2 latest recommended patches applied ..all SUN cluster patches applied. SUN cluster software installed without... (2 Replies)
Discussion started by: samar
2 Replies

9. Solaris

Cable link down

We are unable to ping from Sun Ultra 60 to Ultra 10 machine and vice versa. We are getting an error message Cable Link Down ?. It was working fine. Troubleshooting steps taken. 1) Changed the IPaddresses on both machines 192.168.10.10 and 192.168.10.20. These machines connected through 8 port... (2 Replies)
Discussion started by: vijaykrishna
2 Replies

10. Red Hat

Different hostnames with reboot while lan cable, no lan cable

I am facing strange problem regarding hostname on my Linux(2.6.18-164.el5xen x86_64 GNU/Linux), the hostname changes if reboot with lan cable and with NO lan cable Reboot with lan cable: The hostname is ubunut Unable to connect Oracle database using sqlplus some times database is not... (2 Replies)
Discussion started by: LinuxLearner
2 Replies
bubbros-server(6)						   Games Manual 						 bubbros-server(6)

NAME
bubbros-server - the bub-n-bros server. SYNOPSIS
bubbros-server [ level-file.bin ] [options] DESCRIPTION
bubbros-server starts an http server that acts as a control panel for the server. The server listens on port 8000 by default. The url for the control panel is http://server:port/0xN where 0xN is a random hex number (acts as minimal protection). This url is printed when the server starts. You can start and view games and kill the server from this panel. The control panel also allows you to type in the address of a server to connect to, the script will then open a client to that server. The http server also servers java applet clients for those players who wish to use one. When a game is started the script opens a port for the game server. This port can then be connected to by a client. Clients autodetect servers running on the local network with UDP ping on port 8056. Connection forming The client forms a tcp connection to the server. Or, when using the metaserver, the server forms a connection to the client. If this fails, the client and server try a simultaneous SYN connect. This sometimes works if the server and client are behind firewalls. The server then tries to transmit the data over udp. If it gets no response from the client it will fall back to the existing tcp connection. OPTIONS
-b N, --begin N, --start N Start at board (level) number N. The default is 1. See also the -s option. -h, --help Display help. -i, --infinite Restart the server at the end of the game. Normally the server quits after a certain period of inactivity. This is useful when used with the -m option to make a public server that is available for a long time. -l N, --lives N Limit number of lives to N. If this option is not specified the number of lives will be infinite. -m, --metaserver Register server with the Metaserver (currently) at codespeak.net:8050. This makes your server visible to everybody, and also facil- itates joining through a fascistic firewall. --port TYPE=N Sets default listening ports. If type is LISTEN , sets the game server port to N. The game server port is chosen randomly by default. If the type is HTTP , sets the http server port to N. The http server port defaults to 8000. Another port will be chosen if none was specified and 8000 is already in use. The server also listens to UDP ping on port 8056. -s N, --step N Increase board number with N when a board is completed. Defaults to 1. see also the -b option. OUTPUT
The server outputs helpful debug information concerning the http and game servers. SEE ALSO
bubbros(6) bubbros-client(6) December 7, 2007 bubbros-server(6)
All times are GMT -4. The time now is 08:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy