06-25-2009
Hi Incredible, no is the short answer.
Any attempt to get through to the network results in the hme:0 link down problem.
---------- Post updated at 03:25 PM ---------- Previous update was at 02:30 PM ----------
In case it makes any difference, this is not a desktop, it is a floor standing server of some stature. Enterprise E150 server.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies
2. UNIX for Advanced & Expert Users
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?
Thanx :)
-Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies
3. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
4. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
5. Solaris
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies
6. Solaris
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies
7. Solaris
Hi All,
1. modify /etc/default/login file as
make commented # console=
2.put my laptops ip at both
/etc/inet/ipnodes and /etc/host file
still i can login via telnet/ftp through a DB9-serial cable, but when i tried
through a lan stratight cable directly connected that machine... (7 Replies)
Discussion started by: mahadib
7 Replies
8. Solaris
Hi all,
really interesting thing I have encountered . So :
root@host4 # uname -a
SunOS host4 5.9 Generic_122300-31 sun4u sparc SUNW,Sun-Fire-880
root@host4 # scinstall -p
3.2
latest recommended patches applied ..all SUN cluster patches applied.
SUN cluster software installed without... (2 Replies)
Discussion started by: samar
2 Replies
9. Solaris
We are unable to ping from Sun Ultra 60 to Ultra 10 machine and vice versa. We are getting an error message Cable Link Down ?. It was working fine.
Troubleshooting steps taken.
1) Changed the IPaddresses on both machines 192.168.10.10 and 192.168.10.20. These machines connected through 8 port... (2 Replies)
Discussion started by: vijaykrishna
2 Replies
10. Red Hat
I am facing strange problem regarding hostname on my Linux(2.6.18-164.el5xen x86_64 GNU/Linux), the hostname changes if reboot with lan cable and with NO lan cable
Reboot with lan cable:
The hostname is ubunut
Unable to connect Oracle database using sqlplus some times database is not... (2 Replies)
Discussion started by: LinuxLearner
2 Replies
RPING(1) librdmacm RPING(1)
NAME
rping - RDMA CM connection and RDMA ping-pong test.
SYNOPSIS
rping -s [-v] [-V] [-d] [-P] [-a address] [-p port]
[-C message_count] [-S message_size]
rping -c [-v] [-V] [-d] -a address [-p port]
[-C message_count] [-S message_size]
DESCRIPTION
Establishes a reliable RDMA connection between two nodes using the librdmacm, optionally performs RDMA transfers between the nodes, then
disconnects.
OPTIONS
-s Run as the server.
-c Run as the client.
-a address
On the server, specifies the network address to bind the connection to. On the client, specifies the server address to connect to.
-p Port number for listening server.
-v Display ping data.
-V Validate ping data.
-d Display debug information.
-C message_count
The number of messages to transfer over each connection. (default infinite)
-S message_size
The size of each message transferred, in bytes. (default 100)
-P Run the server in persistent mode. This allows multiple rping clients to connect to a single server instance. The server will run
until killed.
NOTES
Because this test maps RDMA resources to userspace, users must ensure that they have available system resources and permissions. See the
libibverbs README file for additional details.
SEE ALSO
rdma_cm(7), ucmatose(1), udaddy(1), mckey(1)
librdmacm 2007-05-15 RPING(1)