I am using LATEX and need to delete all the lines in a file matching:
\begin{work}
I know there are several ways to do this, but I am trying to do it with the substitute command in VI. The problem is I can't get substitute to recognize the character '\'!
Hello,
I am getting very confused as to where should i quote special/metacharacters in shell.
Sometimes i write * directly and it works, othertimes i have to do "*".
Same is the case with other special characters like /,\,.,$,etc.
Can somebody give me link to somewhere where i can found... (1 Reply)
Hi,
I have a file which has special characters. I can't see them when I "vi" the file. But I am sure there are some special un seen characters. How can I see them?
Please help.
Thx (6 Replies)
Hi,
I am reading a file (GC_JAR.log) which has entries like:
511725.629, 0.1122672 secs]
525268.975, 0.1240036 secs]
527181.835, 0.2068215 secs]
527914.287, 0.2884801 secs]
528457.134, 0.2548725 secs]
I want to replace all the entries of "secs]" with just "secs"
Thus, the output... (4 Replies)
When I open a file in vi, I see the following characters:
\302\240
Can someone explain what these characters mean. Is it ASCII format? I need to trim those characters from a file.
I am doing the following:
tr -d '\302\240'
---------- Post updated at 08:35 PM ---------- Previous... (1 Reply)
Hi all,
I was wondering how can i see the special characters like \t, \n or anything else in a file by using Nano or any other linux command like less, more etc (6 Replies)
i need to replace the any special characters with escape characters like below.
test!=123-> test\!\=123
!@#$%^&*()-= to be replaced by
\!\@\#\$\%\^\&\*\(\)\-\= (8 Replies)
Hi All,
I have some text including Turkish characters and the 3rd party application that reads my file does not supporting this character set (at least, I have no control on it).
So, I used below conversion for maximum character support but still have problems with "İ" and "Ş". Application... (5 Replies)
I'm trying to remove '--X' from the whole file and using variables replace $oldvar with $newvar.
I have tried with double quotes but it doesn't seem to work. $newvar is set to /usr/bin/bash. Would appreciate some guidance.
newvar=$(which bash)
oldvar=/bin/bash
sed... (1 Reply)
Discussion started by: itman73
1 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)