06-24-2009
You should not have changed anything on the system. You should have disconnected and reconnect the cable or worst case you should have rebooted the system once since you found out the conflicting IP and isolating it
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies
2. UNIX for Advanced & Expert Users
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?
Thanx :)
-Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies
3. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
4. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
5. Solaris
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies
6. Solaris
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies
7. Solaris
Hi All,
1. modify /etc/default/login file as
make commented # console=
2.put my laptops ip at both
/etc/inet/ipnodes and /etc/host file
still i can login via telnet/ftp through a DB9-serial cable, but when i tried
through a lan stratight cable directly connected that machine... (7 Replies)
Discussion started by: mahadib
7 Replies
8. Solaris
Hi all,
really interesting thing I have encountered . So :
root@host4 # uname -a
SunOS host4 5.9 Generic_122300-31 sun4u sparc SUNW,Sun-Fire-880
root@host4 # scinstall -p
3.2
latest recommended patches applied ..all SUN cluster patches applied.
SUN cluster software installed without... (2 Replies)
Discussion started by: samar
2 Replies
9. Solaris
We are unable to ping from Sun Ultra 60 to Ultra 10 machine and vice versa. We are getting an error message Cable Link Down ?. It was working fine.
Troubleshooting steps taken.
1) Changed the IPaddresses on both machines 192.168.10.10 and 192.168.10.20. These machines connected through 8 port... (2 Replies)
Discussion started by: vijaykrishna
2 Replies
10. Red Hat
I am facing strange problem regarding hostname on my Linux(2.6.18-164.el5xen x86_64 GNU/Linux), the hostname changes if reboot with lan cable and with NO lan cable
Reboot with lan cable:
The hostname is ubunut
Unable to connect Oracle database using sqlplus some times database is not... (2 Replies)
Discussion started by: LinuxLearner
2 Replies
LEARN ABOUT MINIX
usb_mid
usb_mid(7D) Devices usb_mid(7D)
NAME
usb_mid - USB Multi Interface Driver
SYNOPSIS
device@unit-address
DESCRIPTION
The usb_mid driver is a USBA (Solaris Universal Serial Bus Architecture) compliant nexus driver that binds to device level nodes of a com-
posite (multi interface) device if no vendor or class specific driver is available. The usb_mid driver attempts to bind drivers to each of
the composite device's interfaces.
FILES
/kernel/drv/usb_mid 32-bit x86 ELF kernel module
/kernel/drv/amd64/usb_mid 64-bit x86 ELF kernel module
/kernel/drv/sparcv9/usb_mid 64-bit SPARC ELF kernel module
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+------------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+------------------------------+
|Architecture |SPARC, x86, PCI-based systems |
+-----------------------------+------------------------------+
|Availability |SUNWusb |
+-----------------------------+------------------------------+
SEE ALSO
cfgadm_usb(1M), attributes(5), usba(7D)
Writing Device Drivers
Universal Serial Bus Specification 1.0 and 1.1
System Administration Guide: Basic Administration
http://www.sun.com/io
DIAGNOSTICS
In addition to being logged, the following messages may appear on the system console. All messages are formatted in the following manner:
Warning: <device path> (usb_mid<instance number>): Error Message...
Cannot access <device>. Please reconnect.
This device has been disconnected because a device other than the original one has been inserted. The driver informs you of this fact
by displaying the name of the original device.
Device not identical to the previous one on this port. Please disconnect and reconnect.
Same condition as described above; however in this case, the driver is unable to identify the original device with a name string.
Please disconnect and reconnect this device.
A hotplug of the device is needed before it can be restored.
SunOS 5.10 9 Oct 2004 usb_mid(7D)