Hi, I'm new to unix and have absolutely no experience with it. I am trying to change the network setting on the only computer on our network with SCO Unix. We switched ISP's and now have a new set of IP's. I can't for the life of me figure out how to go in and change these settings, please help.... (12 Replies)
I am trying to find out if you can create an ACL for telnet sessions and restrict it to a certain subnet/IP range..
any information or where to look would be greatly appreciated.
thanks (1 Reply)
Hmmm, tough question for me, so I put it here.
I am trying to use shell script or mysql to do the following thing.
tableA, in which all are single ips.
sip
-------
1.2.3.4
8.8.8.8
123.3.32.1
....
and tableB, a list of our group subnets.
subnet
---------
1.0.0.0/8
20.0.1.0/24 (2 Replies)
Hi,
I am trying to write a script which would figure out who has run which command and their IP. As i dont have any clue as to which commands would do this job, i request some gurus to help me on this.
Thanks
Vishwas (2 Replies)
Is there a command that can lookup ip address, subnet mask, gateway, and dns all at the same. I know ifconfig can lookup ip address and subnet mask. I know route -n can lookup gateway. Not sure about a dns command. So I hope there is a way to lookup ip address, subnet mask, gateway, and dns all at... (2 Replies)
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Hi,
I wanted to generate IPv4 address that communicates between client and server that dumps packets into machines..
Please help with the steps..
Am daemon new to networking.. (1 Reply)
I have an input file:
class 1 3 5 10.10.10..0/23 hicks jimmy
class 3 10.12.10.0/22 mike
class.019283 10.10.15.10/20 henry
gym.847585 45 192.168.10.0/22 nancy jim steve maya
The output should look like this:
10.10.10..0/23
10.12.10.0/22
10.10.15.10/20
192.168.10.0/22
I have the... (3 Replies)
I have this subnet file shown below. How can I calculate all ip addresses from that list
103.22.200.0/22
141.101.64.0/18
10.0.0.0/22I need to be able to read the subnet file and print all IPs in those subnet to an out put file (3 Replies)
Hi All,
I am trying to select 30 days older files under current directory ,but not from subdirectory using below command.
find <Dir> -type f -mtime + 30
This command selecting all the files from current directory and also from sub directory .
I read some documention through internet ,... (1 Reply)
Discussion started by: kommineni
1 Replies
LEARN ABOUT FREEBSD
en
EN(4) BSD Kernel Interfaces Manual EN(4)NAME
en -- device driver for Midway-based ATM interfaces
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device en
device atm
device utopia
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_en_load="YES"
DESCRIPTION
The en device driver supports Midway-based ATM interfaces including the Efficient Networks, Inc. ENI-155 and Adaptec ANA-59x0. Midway is an
AAL5 SAR (Segmentation and Reassembly) chip.
For configuring the card for IP see natmip(4).
The following sysctls are recognized by the driver additionally to those handled by utopia(4):
hw.atm.enX.istats
Contains an array of uint32_t with internal driver statistics.
hw.atm.enX.debug
This is a bit map of debugging options. This variable is only available when the driver is compiled with debugging support.
The driver supports the media options sdh, noscramb and unassigned (see utopia(4)).
DIAGNOSTICS
en0 <Efficient Networks ENI-155p> rev 0 int a irq 5 on pci0:16
en0: ATM midway v0, board IDs 6.0, Utopia (pipelined), 512KB on-board RAM
en0: maximum DMA burst length = 64 bytes
en0: 7 32KB receive buffers, 8 32KB transmit buffers allocated
SEE ALSO natm(4), natmip(4), utopia(4), ifconfig(8), route(8)AUTHORS
Chuck Cranor of Washington University implemented en driver in 1996 for NetBSD.
CAVEATS
The driver extensively uses DMA on PCI. The first generation PCI chipsets do not work or exhibit poor performance.
BSD July 16, 2005 BSD