Hi, I'm new to unix and have absolutely no experience with it. I am trying to change the network setting on the only computer on our network with SCO Unix. We switched ISP's and now have a new set of IP's. I can't for the life of me figure out how to go in and change these settings, please help.... (12 Replies)
I am trying to find out if you can create an ACL for telnet sessions and restrict it to a certain subnet/IP range..
any information or where to look would be greatly appreciated.
thanks (1 Reply)
Hmmm, tough question for me, so I put it here.
I am trying to use shell script or mysql to do the following thing.
tableA, in which all are single ips.
sip
-------
1.2.3.4
8.8.8.8
123.3.32.1
....
and tableB, a list of our group subnets.
subnet
---------
1.0.0.0/8
20.0.1.0/24 (2 Replies)
Hi,
I am trying to write a script which would figure out who has run which command and their IP. As i dont have any clue as to which commands would do this job, i request some gurus to help me on this.
Thanks
Vishwas (2 Replies)
Is there a command that can lookup ip address, subnet mask, gateway, and dns all at the same. I know ifconfig can lookup ip address and subnet mask. I know route -n can lookup gateway. Not sure about a dns command. So I hope there is a way to lookup ip address, subnet mask, gateway, and dns all at... (2 Replies)
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Hi,
I wanted to generate IPv4 address that communicates between client and server that dumps packets into machines..
Please help with the steps..
Am daemon new to networking.. (1 Reply)
I have an input file:
class 1 3 5 10.10.10..0/23 hicks jimmy
class 3 10.12.10.0/22 mike
class.019283 10.10.15.10/20 henry
gym.847585 45 192.168.10.0/22 nancy jim steve maya
The output should look like this:
10.10.10..0/23
10.12.10.0/22
10.10.15.10/20
192.168.10.0/22
I have the... (3 Replies)
I have this subnet file shown below. How can I calculate all ip addresses from that list
103.22.200.0/22
141.101.64.0/18
10.0.0.0/22I need to be able to read the subnet file and print all IPs in those subnet to an out put file (3 Replies)
Hi All,
I am trying to select 30 days older files under current directory ,but not from subdirectory using below command.
find <Dir> -type f -mtime + 30
This command selecting all the files from current directory and also from sub directory .
I read some documention through internet ,... (1 Reply)
Discussion started by: kommineni
1 Replies
LEARN ABOUT FREEBSD
setfib
SETFIB(1) BSD General Commands Manual SETFIB(1)NAME
setfib -- execute a utility with an altered default network view
SYNOPSIS
setfib [-F] fib utility [argument ...]
DESCRIPTION
The setfib utility runs another utility with a different routing table. The table number fib will be used by default for all sockets started
by this process or descendants.
ENVIRONMENT
The PATH environment variable is used to locate the requested utility if the name contains no '/' characters.
EXIT STATUS
If utility is invoked, the exit status of setfib is the exit status of utility.
An exit status of 126 indicates utility was found, but could not be executed. An exit status of 127 indicates utility could not be found.
EXAMPLES
Run netstat(1) to view the second routing table.
setfib -F 1 netstat -rn
or
setfib 1 netstat -rn
or
setfib -1 netstat -rn
SEE ALSO setfib(2), setsockopt(2)STANDARDS
The setfib utility is a FreeBSD specific extension. However, many UNIX-like systems have an equivalent function.
HISTORY
The setfib utility appeared in FreeBSD 7.1.
BSD October 20, 2008 BSD