06-17-2009
AIX:Command to get netaddress/subnet address command in IPv4/IP6
AIX:Command to get netaddress/subnet address command in IPv4/IP6
Can anybody help us with a command to retrieve netaddress/subnet address command in IPv4/IP6 on aix machine.
net/subnet address is in the format 172.16.212.0(signifies all 255 machines in an IPv4 network)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, I'm new to unix and have absolutely no experience with it. I am trying to change the network setting on the only computer on our network with SCO Unix. We switched ISP's and now have a new set of IP's. I can't for the life of me figure out how to go in and change these settings, please help.... (12 Replies)
Discussion started by: PBNOSGT
12 Replies
2. SCO
I am trying to find out if you can create an ACL for telnet sessions and restrict it to a certain subnet/IP range..
any information or where to look would be greatly appreciated.
thanks (1 Reply)
Discussion started by: marvin51796
1 Replies
3. Shell Programming and Scripting
Hmmm, tough question for me, so I put it here.
I am trying to use shell script or mysql to do the following thing.
tableA, in which all are single ips.
sip
-------
1.2.3.4
8.8.8.8
123.3.32.1
....
and tableB, a list of our group subnets.
subnet
---------
1.0.0.0/8
20.0.1.0/24 (2 Replies)
Discussion started by: fedora
2 Replies
4. Cybersecurity
Hi,
I am trying to write a script which would figure out who has run which command and their IP. As i dont have any clue as to which commands would do this job, i request some gurus to help me on this.
Thanks
Vishwas (2 Replies)
Discussion started by: loggedout
2 Replies
5. IP Networking
Is there a command that can lookup ip address, subnet mask, gateway, and dns all at the same. I know ifconfig can lookup ip address and subnet mask. I know route -n can lookup gateway. Not sure about a dns command. So I hope there is a way to lookup ip address, subnet mask, gateway, and dns all at... (2 Replies)
Discussion started by: cokedude
2 Replies
6. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
7. AIX
Hi,
I wanted to generate IPv4 address that communicates between client and server that dumps packets into machines..
Please help with the steps..
Am daemon new to networking.. (1 Reply)
Discussion started by: Priya Amaresh
1 Replies
8. Shell Programming and Scripting
I have an input file:
class 1 3 5 10.10.10..0/23 hicks jimmy
class 3 10.12.10.0/22 mike
class.019283 10.10.15.10/20 henry
gym.847585 45 192.168.10.0/22 nancy jim steve maya
The output should look like this:
10.10.10..0/23
10.12.10.0/22
10.10.15.10/20
192.168.10.0/22
I have the... (3 Replies)
Discussion started by: e_mikey_2000
3 Replies
9. Shell Programming and Scripting
I have this subnet file shown below. How can I calculate all ip addresses from that list
103.22.200.0/22
141.101.64.0/18
10.0.0.0/22I need to be able to read the subnet file and print all IPs in those subnet to an out put file (3 Replies)
Discussion started by: e_mikey_2000
3 Replies
10. Shell Programming and Scripting
Hi All,
I am trying to select 30 days older files under current directory ,but not from subdirectory using below command.
find <Dir> -type f -mtime + 30
This command selecting all the files from current directory and also from sub directory .
I read some documention through internet ,... (1 Reply)
Discussion started by: kommineni
1 Replies
LEARN ABOUT DEBIAN
condor_power
condor_power(1) General Commands Manual condor_power(1)
Name
condor_power send - packet intended to wake a machine from a low power state
Synopsis
condor_power [-h]
condor_power[-d] [-m MACaddress] [-s subnet] [ClassAdFile]
Description
condor_powersends one UDP Wake on LAN (WOL) packet to a machine specified either by command line arguments or by the contents of a machine
ClassAd. The machine ClassAd may be in a file, where the file name specified by the optional argument ClassAdFileis given on the command
line. With no command line arguments to specify the machine, and no file specified, condor_powerquietly presumes that standard input is the
file source which will specify the machine ClassAd that includes the public IP address and subnet of the machine.
condor_powerneeds a complete specification of the machine to be successful. If a MAC address is provided on the command line, but no subnet
is given, then the default value for the subnet is used. If a subnet is provided on the command line, but no MAC address is given, then
condor_powerfalls back to taking its information in the form of the machine ClassAd as provided in a file or on standard input. Note that
this case implies that the command line specification of the subnet is ignored.
Options
-h
Print usage information and exit.
-d
Enable debugging messages.
-m MACaddress
Specify the MAC address in the standard format of six groups of two hexadecimal digits separated by colons.
-s subnet
Specify the subnet in the standard form of an IP address. Without this option, the default subnet used will be 255.255.255.255, causing
a broadcast.
Exit Status
condor_powerwill exit with a status value of 0 (zero) upon success, and it will exit with the value 1 (one) upon failure.
Author
Condor Team, University of Wisconsin-Madison
Copyright
Copyright (C) 1990-2012 Condor Team, Computer Sciences Department, University of Wisconsin-Madison, Madison, WI. All Rights Reserved.
Licensed under the Apache License, Version 2.0.
See the Condor Version 7.8.2 Manualor http://www.condorproject.org/licensefor additional notices. condor-admin@cs.wisc.edu
September 2012 condor_power(1)