06-11-2009
here we are using only ntp1 and ntp2 is not in use
while pinging npt1 we foound the following output
ping 132.95.160.58
PING 132.95.160.58 (132.95.160.58) 56(84) bytes of data.
--- 132.95.160.58 ping statistics ---
78 packets transmitted, 0 received, 100% packet loss, time 77379ms
wew found that pinging from my local server to ntp server is inhibited that's why we are getting 100% packet loss .
with the same ntp server we had another local server running fine without problems in ntp server there also we found pinging is inhibited
ping 132.95.160.58
PING 132.95.160.58 (132.95.160.58) 56(84) bytes of data.
--- 132.95.160.58 ping statistics ---
10 packets transmitted, 0 received, 100% packet loss, time 9044ms
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi.
i was wondering if anyone can show me or direct me on setting up a ntp server under redhat.. Is there any howtos so i can get familar to it "any good sites" (3 Replies)
Discussion started by: souldier
3 Replies
2. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
3. UNIX for Dummies Questions & Answers
Folks;
I'm setting up a new NTP server to sync time for our network. I have one Linux server that needs to point to that NTP server
My 3 questions are:
1. I added the IP address for the NTP server to the "/etc/hosts" file on the Linux server. Is that all i need to do to make the Linux server... (5 Replies)
Discussion started by: Katkota
5 Replies
4. UNIX for Dummies Questions & Answers
Not connected to the internet so I would like to set up 1 unix machine to be the ntp server and have it sync time to about 30 other machines that are all on an private 10net network?:confused: (3 Replies)
Discussion started by: parrisjr
3 Replies
5. Red Hat
Hi All....
I need to configure NTP server in my network, which is heterogeneous, containing Linux as well as windows systems. I'm planning to configure it on RHEL 5.0. What are the prerequisites for this and do I need to register this server?
Can anyone give me as many information as... (1 Reply)
Discussion started by: Amol21
1 Replies
6. Linux
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
Discussion started by: MichaelLi
1 Replies
7. UNIX for Advanced & Expert Users
hello Guys,
I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message;
Code:
ntpq -p ntpq: read: Connection refused
Here this is the ntp.conf file:
Code:
cat /etc/ntp.conf # BEGIN NTP... (1 Reply)
Discussion started by: dyavuzy1
1 Replies
8. HP-UX
Hi
I wonder if its possible to setup NTP clients running HP-UX o.s. from a solaris 10 NTP server?
FR (3 Replies)
Discussion started by: fretagi
3 Replies
9. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
10. Linux
Hello
I need to create NTP server for all my devices, What is the best OS for NTP Server? "CentOS, Redhat, Ubuntu "
I tried before Ubuntu but some of device not detect the server
Need your recommendation
Thank you (2 Replies)
Discussion started by: moudmm
2 Replies
aseqnet(1) General Commands Manual aseqnet(1)
NAME
aseqnet - ALSA sequencer connectors over network
SYNOPSIS
aseqnet [remotehost]
DESCRIPTION
aseqnet is an ALSA sequencer client which sends and receives event packets over network. Suppose two hosts connected by network, hostA as
a server and hostB as a client. The ALSA sequencer system must be running on both hosts. For creating the server port, run the following
on hostA:
hostA% aseqnet
sequencer opened: 128:0
Then a user client 128 with port 0 was opened on hostA. (The client number may vary.) For creating the (network-)client port, run aseqnet
with the hostname of the server:
hostB% aseqnet hostA
sequencer opened: 132:0
Now all events sent to hostA:128:0 are transferred to hostB:132:0, and vice versa.
The ports created by aseqnet can be connected arbitrary to other sequencer ports via aconnect(1). For example, to connect hostB:132:0 to a
MIDI output device 65:0:
hostB% aconnect 132:0 65:0
Then events to hostA:128:0 will be delivered to hostB:65:0. The following command plays MIDI on hostB.
hostA% pmidi -p 128:0 foo.mid
The multiple clients may exist simultaneously. If hostC is connected as a client to hostA, events from from hostA are sent to all con-
nected network clients, i.e. hostB and hostC. However, only one connection is allowed from a client to a server.
To disconnect network, stop all clients before server by ctrl-C or sending signal to them. The server will automatically quit.
OPTIONS
-p port
Specify the TCP port number or TCP service name.
-s addr
Subscribe to the given address for read automatically.
-d addr
Subscribe to the given address for write automatically.
-v Verbose mode.
SEE ALSO
aconnect(1), pmidi(1)
AUTHOR
Takashi Iwai <tiwai@suse.de>.
January 1, 2000 aseqnet(1)