Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Hello, I am trying to get clarity on a few things and am looking for some info.
In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth.
But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi All,
I have done IEEE 802.3ad Dynamic link aggregation bond configuration with name bond0 which has 4 slaves (each 25GB/s) in it on cent os 6.8. Issue i am facing is bonding throughput is only 50GB/s not 100GB/s. below are the configuration files :
DEVICE=bond0
IPADDR=xx.xx.xx.xx... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
LEARN ABOUT DEBIAN
iblinkinfo
IBLINKINFO(8) OpenIB Diagnostics IBLINKINFO(8)NAME
iblinkinfo.pl - report link info for all links in the fabric
SYNOPSIS
iblinkinfo.pl
[-Rhcdl -C <ca_name> -P <ca_port> -v <lt,hoq,vlstall> -S <guid> -D <direct_route>]
DESCRIPTION
iblinkinfo.pl reports the link info for each port of each switch active in the IB fabric.
OPTIONS -R Recalculate the ibnetdiscover information, ie do not use the cached information. This option is slower but should be used if the
diag tools have not been used for some time or if there are other reasons to believe the fabric has changed.
-S <guid>
Output only the switch specified by <guid> (hex format)
-D <direct_route>
Output only the switch specified by the direct route path.
-l Print all information for each link on one line. Default is to print a header with the switch information and then a list for each
port (useful for grep'ing output).
-d Print only switches which have a port in the "Down" state.
-v <lt,hoq,vlstall>
Verify additional switch settings (<LifeTime>,<HoqLife>,<VLStallCount>)
-c Print port capabilities (enabled and supported values)
-C <ca_name> use the specified ca_name for the search.
-P <ca_port> use the specified ca_port for the search.
AUTHOR
Ira Weiny
<weiny2@llnl.gov>
OpenIB Jan 24, 2008 IBLINKINFO(8)