Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Hello, I am trying to get clarity on a few things and am looking for some info.
In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth.
But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi All,
I have done IEEE 802.3ad Dynamic link aggregation bond configuration with name bond0 which has 4 slaves (each 25GB/s) in it on cent os 6.8. Issue i am facing is bonding throughput is only 50GB/s not 100GB/s. below are the configuration files :
DEVICE=bond0
IPADDR=xx.xx.xx.xx... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
LEARN ABOUT DEBIAN
im-switch
IM-SWITCH(8) System Manager's Manual IM-SWITCH(8)NAME
im-switch - set up input method for X Window
SYNOPSIS
im-switch [-v][-z ll_CC] -s inputmethodname
im-switch [-v][-z ll_CC] -c
im-switch [-v][-z ll_CC] -a
im-switch [-v][-z ll_CC] -l
im-switch -h
im-switch
DESCRIPTION
This manual page very briefly documents the im-switch command.
The im-switch command provides the framework to configure and to switch the input method on X Window System depending on the locale. This
input method is the essential mechanism for Japanese, Chinese and Korean (CJK) languages to enter their non-ASCII native characters.
Some input methods such as IBus, SCIM, and uim support not only one of these CJK languages but support almost all languages simultaneously
by dynamically switching keyboard modes with GUI.
The most desirable input method is provided as the configurable system wide default using Debian alternatives mechanism with /etc/alterna-
tives/xinput-ll_CC link.
The X start up code sources /etc/X11/Xsession.d/90im-switch which read the configuration file and activates the input method. The user
configuration files and links are located in ~/.xinput.d/ . The system configuration files and links are located in /etc/X11/xinit/xin-
put.d/ .
This structure ensures to have different input methods to be installed side-by-side.
im-switch understands the following options:
-v Display verbose message during execution.
-z ll_CC
Set up the input method for X run under ll_CC locale (ISO 639 / ISO 3188). When changing the fallback default for all locales, use
all_ALL as the quasi-locale value here. The setup by this all_ALL does not override specific setups.
-s inputmethodname
Set up the input method to use inputmethodname.
-c Configure the input method with menu. (Under X, this uses GUI.)
-a Reset the input method to the system default.
-l List the input method configuration.
-h Print a help message to the standard output and exit.
When the im-switch command is invoked without any command arguments, it functions as -c option case. This is meant to be used by the GUI
menu.
SEE ALSO update-alternatives(8) /usr/share/doc/im-switch/README.Debian /etc/X11/xinit/xinput.d/default
AUTHOR
This manual page was written by Osamu Aoki <osamu@debian.org>, for the Debian GNU/Linux system (but may be used by others).
IM-SWITCH(8)