Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Hello, I am trying to get clarity on a few things and am looking for some info.
In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth.
But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi All,
I have done IEEE 802.3ad Dynamic link aggregation bond configuration with name bond0 which has 4 slaves (each 25GB/s) in it on cent os 6.8. Issue i am facing is bonding throughput is only 50GB/s not 100GB/s. below are the configuration files :
DEVICE=bond0
IPADDR=xx.xx.xx.xx... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
LEARN ABOUT DEBIAN
fence_brocade
fence_brocade(8) System Manager's Manual fence_brocade(8)NAME
fence_brocade - I/O Fencing agent for Brocade FC switches
SYNOPSIS
fence_brocade [OPTION]...
DESCRIPTION
fence_brocade is an I/O Fencing agent which can be used with Brocade FC switches. It logs into a Brocade switch via telnet and disables a
specified port. Disabling the port which a machine is connected to effectively fences that machine. Lengthy telnet connections to the
switch should be avoided while a GFS cluster is running because the connection will block any necessary fencing actions.
fence_brocade accepts options on the command line as well as from stdin. fenced sends parameters through stdin when it execs the agent.
fence_brocade can be run by itself with command line options which is useful for testing.
After a fence operation has taken place the fenced machine can no longer connect to the Brocade FC switch. When the fenced machine is
ready to be brought back into the GFS cluster (after reboot) the port on the Brocade FC switch needs to be enabled. This can be done by
running fence_brocade and specifying the enable action.
Vendor URL: http://www.brocade.com
OPTIONS -a IPaddress
IP address of the switch.
-h Print out a help message describing available options, then exit.
-l login
Login name for the switch.
-n port
The port number to disable on the switch.
-o action
The action required. disable (default) or enable.
-p password
Password for login.
-S path
Full path to an executable to generate the password for login.
-q Quiet mode: print only error messages.
-V Print out a version message, then exit.
STDIN PARAMETERS
agent = < param >
This option is used by fence_node(8) and is ignored by fence_brocade.
ipaddr = < hostname | ip >
IP address or hostname of the switch.
login = < param >
Login name.
option = < param >
The action required. disable (default) or enable.
passwd = < param >
Password for login.
passwd_script = < param >
Full path to an executable to generate the password for login.
port = < param >
The port number to disable on the switch.
SEE ALSO fence(8), fence_node(8)fence_brocade(8)