Sponsored Content
Special Forums IP Networking bonding without switch link aggregation Post 302324355 by Eruditass on Wednesday 10th of June 2009 01:49:59 PM
Old 06-10-2009
heh sorry, yeah that was a typo.

scroll down to mode 6, balance alb
LiNUX Horizon - Bonding (Port Trunking)
Tips and Tuning for Ethernet Bonding With Linux
 

10 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. IP Networking

bonding lacp and link aggregation

Hello, I am trying to get clarity on a few things and am looking for some info. In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth. But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Discussion started by: jaredo
1 Replies

4. HP-UX

Link Aggregation HPUX

Hi, Hoping someone can offer some advice on something i have not dealt with before. We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies

5. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

6. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

7. HP-UX

Break Link Aggregation in HP UX.

Hi, I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900. Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server. So It need to change in cluster script. But I dont know where I have to change it. Please... (1 Reply)
Discussion started by: mkiron
1 Replies

8. Solaris

Link Aggregation without LACP

Hi, I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP? I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies

9. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

10. UNIX for Advanced & Expert Users

Bonding IEEE 802.3ad Dynamic link aggregation : Bond showing less than desired throughput

Hi All, I have done IEEE 802.3ad Dynamic link aggregation bond configuration with name bond0 which has 4 slaves (each 25GB/s) in it on cent os 6.8. Issue i am facing is bonding throughput is only 50GB/s not 100GB/s. below are the configuration files : DEVICE=bond0 IPADDR=xx.xx.xx.xx... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
URI::URL(3)						User Contributed Perl Documentation					       URI::URL(3)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences exist compared to the "URI" class interface: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs. o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path: same as ($uri->abs_path || "/") o $url->netloc: same as $uri->authority o $url->epath, $url->equery: same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters) o $url->params and $url->eparams methods o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag: same as $uri->fragment o $url->keywords: same as $uri->query_keywords o $url->localpath and friends map to $uri->file. o $url->address and $url->encoded822addr: same as $uri->to for mailto URI o $url->groupart method for news URI o $url->article: same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.12.5 2011-08-13 URI::URL(3)
All times are GMT -4. The time now is 03:20 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy