|
|
Sponsored Content
Special Forums
IP Networking
bonding without switch link aggregation
Post 302324355 by Eruditass on Wednesday 10th of June 2009 01:49:59 PM
06-10-2009
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. IP Networking
Hello, I am trying to get clarity on a few things and am looking for some info.
In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth.
But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Discussion started by: jaredo
1 Replies
4. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
5. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
6. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
7. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
8. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. UNIX for Advanced & Expert Users
Hi All,
I have done IEEE 802.3ad Dynamic link aggregation bond configuration with name bond0 which has 4 slaves (each 25GB/s) in it on cent os 6.8. Issue i am facing is bonding throughput is only 50GB/s not 100GB/s. below are the configuration files :
DEVICE=bond0
IPADDR=xx.xx.xx.xx... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
LEARN ABOUT CENTOS
uml_switch
UML_SWITCH(1) General Commands Manual UML_SWITCH(1) NAME
uml_switch -- switch daemon for user-mode Linux SYNOPSIS
uml_switch [-unix control_socket data_socket] [-hub] [-tap tun device] [-compat-v0] [-daemon] DESCRIPTION
This manual page documents briefly the uml_switch program. This manual page was written for the Debian GNU/Linux distribution because the original program does not have a manual page. uml_switch is a daemon for managing a virtual network between user-mode Linux systems, with no connection to the host system's network. It will listen for connections on a pair of UNIX domain sockets, and forward packets between clients which connect to them. OPTIONS
-unix control_socket data_socket Listen on the specified pair of sockets, instead of the defaults. -hub Act like a hub. This means that packets received will be broadcast over all virtual links. The default is to act as a switch, where packets are only sent to the link matching the destination MAC address of the packet. -tap tap device Connect the switch to a dynamically created tap device on the host -compat-v0 Specify control protocol version 0 compatibility. -daemon Run in the background as a daemon. SEE ALSO
linux(1) The UserModeLinux-HOWTO (link to URL http://user-mode-linux.sourceforge.net/UserModeLinux-HOWTO.html) AUTHOR
uml_switch was written by Jeff Dike and others. This manual page was written by Matt Zimmerman mdz@debian.org for the Debian GNU/Linux system (but may be used by others). Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.1 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts and no Back-Cover Texts. UML_SWITCH(1)