06-04-2009
i'm pretty sure it was. I was just wandering if there are any settings that are flushed during a nic bounce? I haven't been able to reproduce this - so could well be user error
Thanks for the reply though.
10 More Discussions You Might Find Interesting
1. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
2. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
3. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
4. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. IP Networking
Hi,
I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0.
I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0.
For example, I'm using eth0 for downloads... (2 Replies)
Discussion started by: Subbeh
2 Replies
9. IP Networking
Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
eth1 Link encap:Ethernet HWaddr 0a:0e:64:18:52:72
inet addr:192.168.10.15
eth1:2 ... (1 Reply)
Discussion started by: faka
1 Replies
10. IP Networking
Hi folks,
I have a debian server running an Apache daemon on the eth0 interface. Now from time to time the server has to open an openvpn connection (tun0) to other networks to get some data from there. During this period the Apache is no longer reachable under it's IP address on eth0 because all... (6 Replies)
Discussion started by: flyingwalrus
6 Replies
ROUTE(8) System Manager's Manual ROUTE(8)
NAME
route - manually manipulate the routing tables
SYNOPSIS
/sbin/route [ -f ] [ -n ] [ command args ]
DESCRIPTION
Route is a program used to manually manipulate the network routing tables. It normally is not needed, as the system routing table manage-
ment daemon, routed(8), should tend to this task.
Route accepts two commands: add, to add a route, and delete, to delete a route.
All commands have the following syntax:
/sbin/route command [ net | host ] destination gateway [ metric ]
where destination is the destination host or network, gateway is the next-hop gateway to which packets should be addressed, and metric is a
count indicating the number of hops to the destination. The metric is required for add commands; it must be zero if the destination is on
a directly-attached network, and nonzero if the route utilizes one or more gateways. If adding a route with metric 0, the gateway given is
the address of this host on the common network, indicating the interface to be used for transmission. Routes to a particular host are dis-
tinguished from those to a network by interpreting the Internet address associated with destination. The optional keywords net and host
force the destination to be interpreted as a network or a host, respectively. Otherwise, if the destination has a ``local address part''
of INADDR_ANY, or if the destination is the symbolic name of a network, then the route is assumed to be to a network; otherwise, it is pre-
sumed to be a route to a host. If the route is to a destination connected via a gateway, the metric should be greater than 0. All sym-
bolic names specified for a destination or gateway are looked up first as a host name using gethostbyname(3N). If this lookup fails, get-
netbyname(3N) is then used to interpret the name as that of a network.
Route uses a raw socket and the SIOCADDRT and SIOCDELRT ioctl's to do its work. As such, only the super-user may modify the routing
tables.
If the -f option is specified, route will ``flush'' the routing tables of all gateway entries. If this is used in conjunction with one of
the commands described above, the tables are flushed prior to the command's application.
The -n option prevents attempts to print host and network names symbolically when reporting actions.
DIAGNOSTICS
``add [ host | network ] %s: gateway %s flags %x''
The specified route is being added to the tables. The values printed are from the routing table entry supplied in the ioctl call. If the
gateway address used was not the primary address of the gateway (the first one returned by gethostbyname), the gateway address is printed
numerically as well as symbolically.
``delete [ host | network ] %s: gateway %s flags %x''
As above, but when deleting an entry.
``%s %s done''
When the -f flag is specified, each routing table entry deleted is indicated with a message of this form.
``Network is unreachable''
An attempt to add a route failed because the gateway listed was not on a directly-connected network. The next-hop gateway must be given.
``not in table''
A delete operation was attempted for an entry which wasn't present in the tables.
``routing table overflow''
An add operation was attempted, but the system was low on resources and was unable to allocate memory to create the new entry.
SEE ALSO
intro(4N), routed(8), XNSrouted(8)
4.2 Berkeley Distribution November 16, 1996 ROUTE(8)