06-04-2009
Was the NIC configured properly with the right IP and the right netmask to reach that subnet?
10 More Discussions You Might Find Interesting
1. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
2. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
3. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
4. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. IP Networking
Hi,
I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0.
I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0.
For example, I'm using eth0 for downloads... (2 Replies)
Discussion started by: Subbeh
2 Replies
9. IP Networking
Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
eth1 Link encap:Ethernet HWaddr 0a:0e:64:18:52:72
inet addr:192.168.10.15
eth1:2 ... (1 Reply)
Discussion started by: faka
1 Replies
10. IP Networking
Hi folks,
I have a debian server running an Apache daemon on the eth0 interface. Now from time to time the server has to open an openvpn connection (tun0) to other networks to get some data from there. During this period the Apache is no longer reachable under it's IP address on eth0 because all... (6 Replies)
Discussion started by: flyingwalrus
6 Replies
route(8c) route(8c)
Name
route - manually manipulate the routing tables
Syntax
/etc/route [ -f ] [ -n ] command args ]
Description
The program is used to manipulate the network routing tables manually. However, normally it is not needed, as the system routing table
management daemon, should tend to this task.
The program accepts two commands: add, to add a route and delete, to delete a route.
All commands have the following syntax:
/etc/route command [ net | host ] destination gateway [ metric ]
In this syntax, destination is a host or network for which the route is to, gateway is the gateway to which packets should be addressed,
and metric is an optional count indicating the number of hops to the destination. The metric is required for add commands. It must be
zero if the destination is on a directly-attached network, and nonzero if the route utilizes one or more gateways.
When adding a route with metric 0, the gateway given is the address of this host on the common network, indicating the interface to be used
for transmission. Routes to a particular host are distinguished from routes to a network by interpreting the Internet address associated
with destination. The optional keywords net and host force the destination to be interpreted as a network or host, respectively. If the
destination has a local address part of INADDR_ANY, then the route is assumed to be to a network. Otherwise, it is presumed to be a route
to a host. If the route is to a destination connected via a gateway, the metric should be greater than 0. All symbolic names specified
for a destination or gateway are looked up first as a host name using If this lookup fails, is then used to interpret the name as that of a
network.
The command uses a raw socket and the SIOCADDRT and SIOCDELRT ioctls to do its work. As such, only the superuser can modify the routing
tables.
Options
-f Flushes the routing tables of all gateway entries. If is used with one of the commands described above, the tables are flushed prior
to the command's application.
-n Prevents attempts to print host and network names symbolically when reporting actions.
Restrictions
The change operation is not implemented. Therefore, you should first add the new route, and then delete the old one.
Diagnostics
add [host | network] %s: gateway %s flags %x"
The specified route is being added to the tables. The values printed are from the routing table entry supplied in the ioctl call. If the
gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically as
well as symbolically.
delete [ host | network] %s: gateway %s flags %x
The specified route is being deleted from the tables. The values printed are from the routing table entry supplied in the ioctl call. If
the gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically
as well as symbolically.
%s %s done
When the flag is specified, each routing table entry that is deleted is indicated with a message of this form.
Network is unreachable
An attempt to add a route failed because the gateway listed was not on a directly-connected network. The next-hop gateway must be given.
not in table
A delete operation was attempted for an entry which was not present in the tables.
routing table overflow
An add operation was attempted, but the system was low on resources and was unable to allocate memory to create the new entry.
See Also
intro(4n), routed(8c)
route(8c)