06-04-2009
Had to bounce interface to add network route
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was trying to use as the gateway.
Any ideas why this happened? is there some kind of lock on the interface while it is in use?
10 More Discussions You Might Find Interesting
1. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
2. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
3. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
4. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. IP Networking
Hi,
I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0.
I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0.
For example, I'm using eth0 for downloads... (2 Replies)
Discussion started by: Subbeh
2 Replies
9. IP Networking
Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
eth1 Link encap:Ethernet HWaddr 0a:0e:64:18:52:72
inet addr:192.168.10.15
eth1:2 ... (1 Reply)
Discussion started by: faka
1 Replies
10. IP Networking
Hi folks,
I have a debian server running an Apache daemon on the eth0 interface. Now from time to time the server has to open an openvpn connection (tun0) to other networks to get some data from there. During this period the Apache is no longer reachable under it's IP address on eth0 because all... (6 Replies)
Discussion started by: flyingwalrus
6 Replies
LEARN ABOUT OPENSOLARIS
tc-route
Route classifier in tc(8) Linux Route classifier in tc(8)
NAME
route - route traffic control filter
SYNOPSIS
tc filter ... route [ from REALM | fromif TAG ] [ to REALM ] [ classid CLASSID ] [ action ACTION_SPEC ]
DESCRIPTION
Match packets based on routing table entries. This filter centers around the possibility to assign a realm to routing table entries. For
any packet to be classified by this filter, a routing table lookup is performed and the returned realm is used to decide on whether the
packet is a match or not.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
from REALM
fromif TAG
Perform source route lookups. TAG is the name of an interface which must be present on the system at the time of tc invocation.
to REALM
Match if normal (i.e., destination) routing returns the given REALM.
EXAMPLES
Consider the subnet 192.168.2.0/24 being attached to eth0:
ip route add 192.168.2.0/24 dev eth0 realm 2
The following route filter will then match packets from that subnet:
tc filter add ... route from 2 classid 1:2
and pass packets on to class 1:2.
NOTES
Due to implementation details, realm values must be in a range from 0 to 255, inclusive. Alternatively, a verbose name defined in
/etc/iproute2/rt_realms may be given instead.
SEE ALSO
tc(8), ip-route(8)
iproute2 21 Oct 2015 Route classifier in tc(8)