Sponsored Content
Operating Systems Solaris Sun Fire v440 hardware problem (can't get ok>) Post 302322185 by lowbyte on Wednesday 3rd of June 2009 04:52:24 AM
Old 06-03-2009
Hi

the message:
0>POST: Return to OBP.

SC Alert: Host System has Reset

Could not read diag-switch? from NVRAM!

shows you error. The ALOM is okay, the POST has run, then the
server will return to OBP, therefor he reads the contents of the NVRAM.
But your NVRAM is flashed, you can't boot or install Solaris, cause
the NVRAM is the BIOS of the V440, where all pathes and infos for
your hardware is been saved.
The only way is to install a new NVRAM, you need a support contract
and a service call, or a new motherboard.

cu
lowbyte
 

10 More Discussions You Might Find Interesting

1. Solaris

Sun Fire V440 and Patch 109147-39

Got an curious issue. I applied 109147-39 to, oh 15 or so various systems all running Jumpstarted Solaris 8. When I hit the first two V440s, they both failed with Return code 139. All non shell commands segfaulted from then on. The patch modified mainly the linker libraries and commands. ... (2 Replies)
Discussion started by: BOFH
2 Replies

2. Solaris

Sun Fire v440 keeps shutting down

Hello, I hope you can help me. I am new to Sun servers and we have a Sun Fire v440 server in which one power supply failed, we are waiting for new one. But now our server is shutting down constantly. Is there any setting with which we can prevent this behaviour? (1 Reply)
Discussion started by: Tibor
1 Replies

3. Solaris

Sun Fire T 2000 Booting problem

Dear All, I am facing a specfic problem with my New SunFire T2000.Recently we bought new sunfire T2000 sparc server.When i am trying to install solaris 10 through cdrom , I get error messgae Error:Last Trap: Instaruction Access Exception {0} ok boot cdrom Boot device:... (6 Replies)
Discussion started by: solaris8in
6 Replies

4. Solaris

error messages in Sun Fire V440

Hello, I am seeing error messages in V440 (OS = solaris 8). I have copied here : The system does not reboot constantly and it is up for last 67 days. One more interesting thing I found, I see errors start appearing at 4:52AM last until 6am and again start at 16:52am on same day.. I... (5 Replies)
Discussion started by: upengan78
5 Replies

5. Solaris

ALOM wont work when KVM connected to Sun Fire V440 server

Hi, I was asked to connect a KVM screen to a Sun Fire V440 last night so I connected it up but no joy and nothing on the KVM screen. I was told that a reboot may fix the problem so connected to the ALOM and rebooted. On the plus side, the KVM screen now works but I lost the ALOM connection. ... (0 Replies)
Discussion started by: jimmy54321
0 Replies

6. Solaris

Firmware password Solaris Sun Fire v440

Hi: I bougth an used Sun Fire v440, and It have a firmware password. When I turn on the server, it ask for firmware password. (I don 't know what is the correct password). I can access to SC, but when I want to access to OBP, Firmware Password appears again. I remove the battery for two hours,... (1 Reply)
Discussion started by: mguazzardo
1 Replies

7. Solaris

Sun Fire v440 Over heat Problem.

Dear Team, I need some expert advice to my problem. We have a Sun Fire v440 in our customer Place. Server is working fine and no hardware deviations are found except one problem that processors generating too much heat. I have verified and found that the room temperature was 26-27 degree.... (5 Replies)
Discussion started by: sudhansu
5 Replies

8. Solaris

Sun-Fire V440 boot disk issue

Hi, I have Sun Fire V440. Boot disks are mirrored. system crashed and it's not coming up. Error message is Insufficient metadevice database replicas located. Use Metadb to delete databases which are broken. Boot disks are mirrored and other disks are ZFS configuration. Please... (2 Replies)
Discussion started by: samnyc
2 Replies

9. Solaris

Removing a disk from SUN Fire V440 running Solaris 8

Hi, I have a SUN Fire V440 server running Solaris 8. One of the 4 disks do not appear when issued the format command. The "ready to remove" LED is not on either. Metastat command warns that this disk "Needs maintenace". Can I just shutdown and power off the machine and then insert an... (5 Replies)
Discussion started by: Echo68
5 Replies

10. Solaris

Sun Fire v440 Hard disk or controller broken? WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1)

Hi, I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error: WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1): SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
nvram(8)						      System Manager's Manual							  nvram(8)

NAME
nvram - manipulate firmware NVRAM variables SYNOPSIS
nvram [ -p ] [ -f filename ] [ -d name ] [ -c ] [ name [= value ]] ... DESCRIPTION
The nvram command allows manipulation of firmware NVRAM variables. It can be used to get or set a variable. It can also be used to print all of the variables or set a list of variables from a file. Changes to NVRAM variables are only saved by clean restart or shutdown. In principle, name can be any string. In practice, not all strings will be accepted. New World machines can create new variables as desired. Some variables require administrator privilege to get or set. The given value must match the data type required for name. Binary data can be set using the %xx notation, where xx is the hex value of the byte. The type for new variables is always binary data. OPTIONS
-d name Deletes the named firmware variable. -f filename Set firmware variables from a text file. The file must be a list of "name value" statements. The first space on each line is taken to be the separator between "name" and "value". If the last character of a line is , the value extends to the next line. -x Use XML format for reading and writing variables. This option must be used before the -p or -f options, since arguments are pro- cessed in order. -c Delete all of the firmware variables. -p Print all of the firmware variables. EXAMPLES
example% nvram boot-args="-s rd=*hd:10" Set the boot-args variable to "-s rd=*hd:10". This would specify single user mode with the root device in hard drive partition 10. example% nvram my-variable="String One%00String Two%00%00" Create a new variable, my-variable, containing a list of two C-strings that is terminated by a NUL. example% nvram -d my-variable Deletes the variable named my-variable. October 28, 2003 nvram(8)
All times are GMT -4. The time now is 06:36 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy