06-02-2009
error messages and configs would be a big help.
7 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I cannot change my gateway. I have five locations (simulated) and i try to ping another of my locations but it says host unreachable and it is showing the gateway as the host i'm pinging withs ip address. I have tried the route command but I couldn't get it to work. Any suggestions on how to... (2 Replies)
Discussion started by: Deuce
2 Replies
2. IP Networking
Hello there:
I have these situation : I have a unix sco openserver 5.0.7 box and a windows server 2003.
There is a main office and 2 remote office that log in trough a vpn tunnel.
One tunnel From Main to remote1 and the other from Main to remote 2.
Problem! The dsl connection i have is... (2 Replies)
Discussion started by: josramon
2 Replies
3. AIX
Please, anybody help on resolving the following problem?
I have 2 netwotks ( 10.0.0.0 and 10.0.11.0 ) on 2 different areas
I need both networks to telnet the corresponding ethernet card.
This is a prblem because AIX is configured with a default gateway.
Please advice how to assign 2... (2 Replies)
Discussion started by: mynikolas
2 Replies
4. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
5. Shell Programming and Scripting
Hi,
I want to configure 2-gateways in Linux .
Please tell me how I can achieve this. I am accesing 2-internet
connection through these 2-gateways. So I am looking that
if 1-gets down then also other one is working.
Regards
JAGDISH (1 Reply)
Discussion started by: jagdish.machhi@
1 Replies
6. AIX
I have a bunch of servers on AIX, we have at least 2 NIC cards in each of them.
We upgraded them from AIX 4.2 to AIX 5.2. Since then when we reboot a server its always coming up with 2 default gateways. Habitually this is not a problem but sometime its causing some connection problem. We... (10 Replies)
Discussion started by: ce9888
10 Replies
7. UNIX for Dummies Questions & Answers
Hi all. Linux noob here.
I was hoping someone could help me with configuring some routing rules on my router, an Asus AC68.
The router is connected to two gateways, wan0_gateway and wan1_gateway.
I have rules set up in the router gui that will push all traffic from every IP other than my own... (0 Replies)
Discussion started by: Bishi
0 Replies
LEARN ABOUT DEBIAN
seivots-summary
SEIVOTS-SUMMARY(1) General Commands Manual SEIVOTS-SUMMARY(1)
NAME
seivots-summary - summarize seivot output files
SYNOPSIS
seivots-summary [--config=FILE] [--dump-config] [--dump-memory-profile=METHOD] [--dump-setting-names] [--generate-manpage=TEMPLATE] [-h]
[--help] [--list-config-files] [--log=FILE] [--log-keep=N] [--log-level=LEVEL] [--log-max=SIZE] [--log-mode=MODE] [--no-default-configs]
[--output=FILE] [--version] [FILE]...
DESCRIPTION
seivots-summary reads some benchmark result files created by summain(1), and produces summaries of them in tabular form, making it easy to
compare results from different benchmark runs.
OPTIONS
--config=FILE
add FILE to config files
--dump-config
write out the entire current configuration
--dump-memory-profile=METHOD
make memory profiling dumps using METHOD, which is one of: none, simple, meliae, or heapy (default: simple)
--dump-setting-names
write out all names of settings and quit
--generate-manpage=TEMPLATE
fill in manual page TEMPLATE
-h, --help
show this help message and exit
--list-config-files
list all possible config files
--log=FILE
write log entries to FILE (default is to not write log files at all); use "syslog" to log to system log, or "none" to disable log-
ging
--log-keep=N
keep last N logs (10)
--log-level=LEVEL
log at LEVEL, one of debug, info, warning, error, critical, fatal (default: debug)
--log-max=SIZE
rotate logs larger than SIZE, zero for never (default: 0)
--log-mode=MODE
set permissions of new log files to MODE (octal; default 0600)
--no-default-configs
clear list of configuration files to read
--output=FILE
write output to FILE, instead of standard output
--version
show program's version number and exit
EXAMPLE
To summarize all benchmark files:
seivots-summary $HOME/obnam/benchmarks/*/*.seivot | less -S
SEE ALSO
seivot(1), obnam(1).
SEIVOTS-SUMMARY(1)