Anyone,
I am trying to mount a second hard drive on a sunfire V120 w/solaris 5.8. I took this hard drive from another system because I deleted some files off that system and I want to mount it to another system so I can copy the file back onto the system. I really have no other means of... (2 Replies)
Good morning,
I have a problem replacing a disk with raid-5 volumes.
An hardware error was occurred from a disk c9t3 so all slices were in maintenace. Every slice is part of a raid-5 volume. Any replica is present.
Following Volume manager manual for replacing a disk, I have:
- phisically... (0 Replies)
hi
i am wondering if it is possible to use one nfs mount point for several logical volumes.
i have a top level directory /imaging with data1 - data50 below it. each dataX directory is a logical volume configured through LVM. if i mount them separately on the client (i.e. 50 lines in fstab... (1 Reply)
Hey there, sorry if this is a bit too much of a noob question, trying to get to grips with a simple bash script - but i have done ZERO bash scripting.
basically having worked out how to mount and unmount disks using:
disktool -m *device* & disktool -e *device*
- and looking at the result of... (2 Replies)
I am working with a Sun StoredgeTek 6540 disk array connected to two Sun 490 servers. After taking one of the 490 nodes on the cluster down to single user mode I proceeded to install the latest cluster patch from Oracle. After the patch was completed the system rebooted, failed to rejoin the... (2 Replies)
Hi all,
i must add a new disk on a LPAR.
I've done all the HMC and VIOS Procedure to create a virtual host with disk and assign it to lpar.
I don't remember how i must do on the lpar to see this disk. (i use lvm not veritas).
Thanks in advance and sorry for my english.
Bye
Mario (2 Replies)
So. My system have 2 solaris10 machine but system disk of machine 1 data crash.I bring the system disk of machine 1 install on machine2 for get data from disk machine1 but I can't mount disk. because msg is
bash-3.00# mount /dev/dsk/c1t3d0s0 /mnt
mount: /dev/dsk/c1t3d0s0 is not this fstype... (3 Replies)
Hi folks,
because of disk space problem my root is almost full..The root is mounted on rpool and i want to move /app on a new disk, is that possible without compromising any link?How can i do that?
I use solaris 10
Thank you in advance,
Matt
---------- Post updated at 04:36 PM... (8 Replies)
Discussion started by: mattpunk
8 Replies
LEARN ABOUT FREEBSD
msdos
MSDOSFS(5) BSD File Formats Manual MSDOSFS(5)NAME
msdosfs -- MS-DOS file system
SYNOPSIS
options MSDOSFS
DESCRIPTION
The msdosfs driver will permit the FreeBSD kernel to read and write MS-DOS based file systems.
The most common usage follows:
mount -t msdosfs /dev/ada0sN /mnt
where N is the partition number and /mnt is a mount point. Some users tend to create a /dos directory for msdosfs mount points. This helps
to keep better track of the file system, and make it more easily accessible.
It is possible to define an entry in /etc/fstab that looks similar to:
/dev/ada0sN /dos msdosfs rw 0 0
This will mount an MS-DOS based partition at the /dos mount point during system boot. Using /mnt as a permanent mount point is not advised
as its intention has always been to be a temporary mount point for floppy and ZIP disks. See hier(7) for more information on FreeBSD direc-
tory layout.
SEE ALSO mount(2), unmount(2), mount(8), mount_msdosfs(8), umount(8)AUTHORS
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org>.
BSD October 1, 2013 BSD