06-01-2009
This can be a tough concept to grasp - I'll list the steps I do.
1. Edit VIO profile from the HMC like you list in #2.
- I noticed that the steps you listed in #2 go into the 'Dynamic Logical Partitioning' but be careful because if you don't make changes to the profile also then when you reboot the lpar (VIO or client) all changes will be lost.
- Make sure you put a checkmark in 'Access external network Trunk priority'. Also , make note of which adapter ID you give it (it doesn't matter what the number is, this will be used later when you do the mkvdev command). I used 23 because we have a .23.xxx network segment and a .41.xxx segment (you can guess what I used for the other virtual ethernet adapter id).
2. Edit the lpar client's profile from the HMC and do all of the steps you listed under #2
- BUT do NOT put a checkmark in 'Access external network'
- Use the same Adapter ID you made note of in my Step 1. I also use the same ID for the VLAN ID.
3. Create the SEA on VIO1 - (on our system the 23 segment cable is plugged into ent1)
Example from my VIO1:
# lsdev -Cc adapter |grep ent
ent0 Available 02-08 10/100/1000 Base-TX PCI-X Adapter (14106902)
ent1 Available 0A-00 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent2 Available 0A-01 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent3 Available 08-08 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent4 Available 08-09 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent5 Available Virtual I/O Ethernet Adapter (l-lan)
ent6 Available Virtual I/O Ethernet Adapter (l-lan)
## Find 23 segment (C23) virtual adapter (Ex. ent5)
# lscfg | grep ent | grep Virtual
* ent5 U9117.MMA.10FF11F-V3-C23-T1 Virtual I/O Ethernet Adapter (l-lan)
* ent6 U9117.MMA.10FF11F-V3-C41-T1 Virtual I/O Ethernet Adapter (l-lan)
## So we will create the SEA using ent1 as the physical adapter and ent5 as the virtual adapter
$ mkvdev -sea ent1 -vadapter ent5 -default ent5 -defaultid 23
4. Boot the client lpar or run cfgmgr if it's already up and running - then configure the adapter as usual with 'smitty tcpip'
Hope this helps.
Homeyjoe
9 More Discussions You Might Find Interesting
1. AIX
Hi,
I define 2 new LV on the vio server and run a cfgmgr on the partition and see my 2 new hdisk (hdisk6 and hdisk7).
I extend my vg vg000 (on the partition) and add the 2 hdisks.
I had a filesystem on the vg000 and when I added the disk I would like to increase the filesystem. But I cannot do a... (0 Replies)
Discussion started by: touny
0 Replies
2. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
3. AIX
We're using VIO (not an HMC) to manage our LPAR's We have 3 physical adapters and 4 LPARs. Through the VIO interface we assigned 2 virtual interfaces but require a 3rd interface assigned to these LPARs. I am experiencing issues understanding exactly how to create another virtual adapter, either... (1 Reply)
Discussion started by: scottsl
1 Replies
4. AIX
Whenever I assign/unassign a CDROM ( RAID CTRL ) to Active LPAR from HMC, I have to reboot the LPAR.
How can I do it without rebooting the LPARS.
POWER6 with HMC
LPARS = AIX 6.1
Any info
developerWorks : AIX and UNIX : PowerVM Forum : Moving CD-ROM/DVD-ROM dynamically ...
But... (5 Replies)
Discussion started by: filosophizer
5 Replies
5. AIX
Lucky me, someone has installed a server and got it running with the best intentions, but leaving me a headache. :wall:
We have a simple p520 with 4 disks. 2x145Gb & 2x300Gb. The smaller disk pair have been built into a VIO mirrored rootvg, and quite right too.
The other two disks form a... (3 Replies)
Discussion started by: rbatte1
3 Replies
6. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
7. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
8. AIX
Hi,
I just successfully build a Virtual Machine in virtual box with Perfectly running HMC v7. I have a IBM eServer pSeries Model 630 Model 6C4 (Power 4) i.e. 7024-6C4. I am not able to have it connect to the HMC console on the Virtual Box.
Can anyone help me on how to connect it to the... (8 Replies)
Discussion started by: uzair_rock
8 Replies
9. AIX
I have a broken PV in a VIO VG that's used to support client LPARs using LVs. On the client LPAR, I reduced all PVs from the relevant client VG and thus deleted it. I.e. there is no client LPAR using the VIO VG. Yet when I try to reducevg the VIO VG, it complains that the LV hosted on the PV is... (2 Replies)
Discussion started by: maraixadm
2 Replies
LEARN ABOUT DEBIAN
vdetelweb
VDETELWEB(1) General Commands Manual VDETELWEB(1)
NAME
vdetelweb - Virtual Distributed Ethernet Telnet and/or Web management module
SYNOPSIS
vdetelweb [ --web ] [ --telnet ] [ --nodename nodename ] [ --daemon ] [ --rcfile rcfile ] mgmt_socket
DESCRIPTION
vdetelweb implements a tiny telnet server and/or a tiny web server for the remote management of a VDE2 switch.
OPTIONS
-w, --web
start the web server. At least one of --web or --telnet must be set.
-t, --telnet
start the telnet server. At least one of --web or --telnet must be set.
-n, --nodename nodename
specify the nodename as seen from remote connections (e.g. in the command prompt or in the web page title). uname nodename is used
when this option is not specified.
-d, --daemon
run as a daemon, using syslog for logging.
-f, --rcfile rcfile
rc file to set the initial switch configuration. When not specified, vdetelweb searches for ~/.vde/vdetelwebrc and /etc/vde/vdetel-
webrc. At leas one rc file must exist and be readable.
-h, --help
print help. please use it for a more complete list of options.
mgmt_socket
is the managemnt socket used to communicate with the vde_switch. (This option must match the path used in the -M option for the
vde_switch).
NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik"
i.e. the German "Association for Electrical, Electronic & Information Technologies").
SEE ALSO
vde_switch(1), vde_plug(1), vdeq(1). dpipe(1). unixterm(1).
AUTHOR
VDE is a project by Renzo Davoli <renzo@cs.unibo.it>
Virtual Distributed Ethernet June 16, 2008 VDETELWEB(1)