|
|
Sponsored Content
Operating Systems
Solaris
Network Interfaces
Post 302321086 by fugitive on Saturday 30th of May 2009 03:45:54 AM
05-30-2009
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
7. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
8. UNIX for Dummies Questions & Answers
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies
9. AIX
Hi,
I would like to know after the installation of vio server. how many logical network interfaces will be created on vio server if I am having two physical interfaces on vio server.
I am asking this question because I would like know to on the basis of logical network interfaces creation on... (0 Replies)
Discussion started by: manoj.solaris
0 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
LEARN ABOUT DEBIAN
inetutils-ifconfig
IFCONFIG(1) User Commands IFCONFIG(1) NAME
ifconfig - configure network interfaces SYNOPSIS
ifconfig [OPTION...] DESCRIPTION
NAME [ADDR] [broadcast BRDADDR] [pointopoint|dstaddr DSTADDR] [netmask MASK] [metric N] [mtu N] [txqueuelen N] [up|down] [FLAGS] Configure network interfaces. -a, --all display all available interfaces -A, --address=ADDR set interface address to ADDR -B, -b, --broadcast=ADDR, --brdaddr=ADDR set broadcast address to ADDR -d, -p, --dstaddr=ADDR, --peer=ADDR set destination (peer) address to ADDR --down shut the interface down --format=FORMAT select output format (or set back to default) -F, --flags=FLAG[,FLAG...] set interface flags -i, --interface=NAME configure network interface NAME -m, --netmask=MASK set netmask to MASK --metric=N set metric of interface to N -M, --mtu=N set mtu of interface to N -s, --short short output format --up activate the interface (default if address is given) -v, --verbose output information when configuring interface Linux-specific options -T, --txqlen=N set transmit queue length to N -?, --help give this help list --usage give a short usage message -V, --version print program version Mandatory or optional arguments to long options are also mandatory or optional for any corresponding short options. Known flags are: allmulti, automedia, debug, loopback, multicast, portsel, running, trailers, up AUTHOR
Written by Marcus Brinkmann. REPORTING BUGS
Report bugs to <bug-inetutils@gnu.org>. COPYRIGHT
Copyright (C) 2011 Free Software Foundation, Inc. License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>. This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. SEE ALSO
The full documentation for ifconfig is maintained as a Texinfo manual. If the info and ifconfig programs are properly installed at your site, the command info ifconfig should give you access to the complete manual. GNU inetutils 1.9 December 2011 IFCONFIG(1)