ethernet Post: 302320942

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Ethernet

We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time...

2. UNIX for Dummies Questions & Answers

Ethernet Initialisation

I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by...

3. Cybersecurity

Ethernet sniff.

I suspect that someone is using a sniffer on my Ethernet connection, OS X 10.3.9, DSL, ok, I'm in terminal using the "ifconfig" command > flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384 right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the...

4. UNIX for Advanced & Expert Users

Virtual Ethernet

I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up?

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

6. Solaris

ethernet problem

Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args: SunOS Release 5.8 Version Generic_108528-29 64-bit Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved. ifconfig: plumb: qfe2: Bad file number configuring IPv4 interfaces: eri0. moving addresses...

7. AIX

ethernet down

Hello everyone I have a problem with one server, has Aix 5.3 in the errpt has this message IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN F3931284 ...

8. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter...

9. Linux

ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0. Here's what I did: created file /etc/modprobe.d/bonding.d and added the following to it: alias bond0 bonding options bonding...

LEARN ABOUT DEBIAN

freecell-solver-range-parallel-solve

HOOLA(6)							  Freecell Solver							  HOOLA(6)

NAME

       freecell-solver-range-parallel-solve - The Freecell Solver utility for solving a range of Microsoft Freecell/Freecell Pro Boards

SYNOPSIS

       freecell-solver-range-parallel-solve start end print_step [--binary-output-to filename] [--total-iterations-limit limit] [fc-solve
       Arguments...]

DESCRIPTION

       freecell-solver-range-parallel-solve is a command line application that solves a range of Freecell deals of Microsoft Freecell and Freecell
       Pro.

       start is the first board to solve; end is the last (inclusive) and print_step is the division of board numbers in which to print a status
       message.

       Following this three mandatory parameters are several flags specific to the range solve. (refer to the OPTIONS section for more
       information)

       Afterwards one can give it a fc-solve command line that it will use to solve each board. Refer to the fc-solve(6) man page for information
       about its options.

OPTIONS

       --total-iterations-limit sets the maximal number of iterations with which to try to solve each deal. After that, the program will give up
       and report that the board was intractable.

       --binary-output-to sets the filename into which to output the number of iterations it took to solve each board. This file can later be used
       with statistical preset optimizers such as those found in the Freecell Solver version control repository.

SEE ALSO

       fc-solve(6)

AUTHOR

       Shlomi Fish, <http://www.shlomifish.org/> .

Freecell Solver 3.12.0						    2012-06-22								  HOOLA(6)