Sponsored Content
Operating Systems HP-UX Pid X killed due to text modification or page I/O error Post 302320163 by savus on Wednesday 27th of May 2009 08:03:18 AM
Old 05-27-2009
Pid X killed due to text modification or page I/O error

Hello everybody,

I have a HP-UX B.11.11.
I had one disk and added one new.
When trying to configure the second disk Not Using the Logical Volume Manager(from SAM) I have this error:
Code:
Pid X killed due to text modification or page I/O error

I tryed to add another partion on the first disk, but I ended with to same error. I managed to add another swap partition with success on the first disk.
I runed xstm on both disks to check them for harware failures but it seems that they are OK.
I saw also a strange message in system log:
Code:
Synchronous Page I/O error occurred while paging to/from disk

Can anybody help me with this issue?
Thank you in advance!
Stefan
 

10 More Discussions You Might Find Interesting

1. Programming

Text Modification and page I/O error

Hi!, while launching my C application on HP-UX 10.2 workstation, I get the following error message sometime: Pid 9951 killed due to text modification or page I/O error Could someone tell me what does this error means?? and how is this caused? Thanx in Advance, JP (4 Replies)
Discussion started by: jyotipg
4 Replies

2. Filesystems, Disks and Memory

finding out the pid for a busy text file

Can some one please tell me how to find out the proccess ID that is holding up a file. I am attempting to remove a file and I am getting a message stating that it is busy. i.e rm filename filename: 777 mode ? (y/n) y rm: filename not removed. Text file busy Thanks in advance. (1 Reply)
Discussion started by: jxh461
1 Replies

3. Shell Programming and Scripting

SED for text file modification

Hi all, i have a text file something like that FLAG DATE(YYYYMMDD) TIME(HHMMSS) FLAG1 DATE20060101 141216 FLAG1 DATE20070101 141216 FLAG2 DATE20060102 140010 FLAG2 DATE20060103 101212 FLAG1 ... (6 Replies)
Discussion started by: gfhgfnhhn
6 Replies

4. HP-UX

Pid killed due to trashed stack

Hi when im running an application in load im getting pid 2433 killed due to trashed stack Pid 2433 was killed due to failure in writing the signal context. when we ll get this type of problem.any solnnnn plz give reply this is my system config: HP-UX devusp2 B.11.11 U 9000/800... (1 Reply)
Discussion started by: pramod123
1 Replies

5. UNIX for Advanced & Expert Users

Problem due to Fork Error

Hi, I have developed a datastage job...which has many process running in parallel..but because of Fork Error my job is not working:( Can any body help me out to solve this Fork error problem.:rolleyes: My Os is SUNOS. IS there any setting in Unix through admin where in if i set some paramter... (8 Replies)
Discussion started by: Amey Joshi
8 Replies

6. Shell Programming and Scripting

aborted due to compilation error

I wanted to edit the time for a cron job that cleans out the quarantine in mailscanner. etc/cron.daily/clean.quarantine I edited the file #!/usr/bin/perl # # IMPORTANT NOTE: # # Change the next line to 0 instead of 1 to enable this script. # By default it will be disabled and... (2 Replies)
Discussion started by: mcraul
2 Replies

7. Shell Programming and Scripting

Text string modification

My shell needs to take a 10 digit number and output it in the forum nnn-nnn-nnnn I considered using the fold command but that won't help too much. (11 Replies)
Discussion started by: computethis
11 Replies

8. Shell Programming and Scripting

bc syntax error due to sed

Hi all, before posting this questions i have looked up and found similar cases as the one i have but none of them had the answer i was lookink for. i have the next two commands (with their corresponding output) e1=$(grep KCAL input.OUT | sed 's/ FINAL HEAT OF FORMATION = ... (2 Replies)
Discussion started by: ezitoc
2 Replies

9. Shell Programming and Scripting

Grep text matching problem with script which checks if web page contains text.

I wrote a Bash script which checks to see if a text string exists on a web page and then sends me an email if it does (or does not e.g. "Out of stock"). I run it from my crontab, it's quite handy from time to time and I've been using it for a few years now. The script uses wget to download an... (6 Replies)
Discussion started by: gencon
6 Replies

10. Shell Programming and Scripting

Help with text modification and displaying

I have a file storing some text and another file storing some numbers I want to display characters other than the specified place of strings one.txt xyz abc 233 skfo 4r443 sfs abc abcd sd fsdf sdfd abc 11 abc 33 abc dsaf two.txt Nt_djd_k='5-6,7-9' Nt_hh_l='3-6,7-8' a=`grep... (4 Replies)
Discussion started by: rahulsk
4 Replies
volunroot(8)						      System Manager's Manual						      volunroot(8)

NAME
volunroot - Remove Logical Storage Manager hooks for rootable volumes SYNOPSIS
/usr/sbin/volunroot [-a | -A] OPTIONS
Specifies that all volumes on the system disk be converted back to UNIX disk partitions, not just the root and swap volumes, rootvol and swapvol. Forces removal of the private region unless it is the last one in the system. DESCRIPTION
The volunroot script can be used to restore the accessibility of the root, swap, and other file systems on the boot disk directly through disk partitions instead of through volume devices. The script also removes other changes that were made to enable booting of the system from the root volume, so that the system will boot with no dependency on the Logical Storage Manager. When used with no options, volunroot affects only the root and swap volumes, rootvol and swapvol. For volunroot to work properly, only one plex must exist for each of the affected volumes. This plex must be the one created by volrootmir or the original plex created when the root disk was encapsulated. This ensures that the underlying subdisks will have equivalent partitions defined for them on the disk. If these conditions are not met, the volunroot operation fails and none of the volumes are converted to disk partitions. The unwanted plexes can be removed using either voledit or volplex. SEE ALSO
volencap(8), voldiskadm(8), voledit(8), volintro(8), volplex(8), volrootmir(8) volunroot(8)
All times are GMT -4. The time now is 04:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy