05-20-2009
Used the correct instance but still getting "operation failed"
# ndd -set /dev/le instance 0
operation failed, Invalid argument
# ndd -set /dev/le adv_10fdx_cap 1
operation failed, Invalid argument
# ndd -set /dev/le adv_autoneg_cap 0
operation failed, Invalid argument
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub.
Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to.
... (4 Replies)
Discussion started by: merlin
4 Replies
2. UNIX for Dummies Questions & Answers
Dear Members,
I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
Discussion started by: Phobos
4 Replies
3. Programming
what is meant by full duplex and half duplex?
b'coz in differences b\w hub and switch ,i heard lot this duplex word
so please help me (1 Reply)
Discussion started by: parvathy
1 Replies
4. Solaris
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies
5. SuSE
How do I configure full duplex on suse 8.2
I tried
ethtool -s eth0 speed 100 duplex full autoneg off
the above works but when I reboot the machine the configure was lost.
How do I configure full duplex so that when the machine get rebooted the configuration will stay.
My interface... (4 Replies)
Discussion started by: hassan2
4 Replies
6. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
7. Programming
Hello,
here's my situation: I have a C++ server running on a well known machine and a number of Java clients running on other machines (assumed as unknown) on the same LAN. What I want to achieve is full duplex communication between those applications, in order to exchange complex objects and data... (3 Replies)
Discussion started by: demerzel3
3 Replies
8. Red Hat
Hi all,
I've changed eth0 to (#ethtool eth0):
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
and (#cat /etc/sysconfig/network-scripts/ifcfg-eth):
ETHTOOL_OPTS="autoneg off speed 1000... (3 Replies)
Discussion started by: faraaris
3 Replies
9. UNIX for Advanced & Expert Users
Hi,
I have been trying to connect two computers directly through their LAN cards. One is a 3com 3c905c 10/100 Mbit/s card and the other is an Intel i217-lm 10/100/1000Mbit/s card. I have connected them through a CAT 6 cable. Whenever autoneg is turned on, the PCs connect in the 10Mb/s mode, and... (7 Replies)
Discussion started by: jamie_123
7 Replies
ndd(1M) System Administration Commands ndd(1M)
NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)
NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)