05-18-2009
cat /etc/release
Solaris 2.5.1 SPARCserver-1000
I have no idea that "le" supports 10 mbit. I just want to make "le" full duplex.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub.
Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to.
... (4 Replies)
Discussion started by: merlin
4 Replies
2. UNIX for Dummies Questions & Answers
Dear Members,
I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
Discussion started by: Phobos
4 Replies
3. Programming
what is meant by full duplex and half duplex?
b'coz in differences b\w hub and switch ,i heard lot this duplex word
so please help me (1 Reply)
Discussion started by: parvathy
1 Replies
4. Solaris
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies
5. SuSE
How do I configure full duplex on suse 8.2
I tried
ethtool -s eth0 speed 100 duplex full autoneg off
the above works but when I reboot the machine the configure was lost.
How do I configure full duplex so that when the machine get rebooted the configuration will stay.
My interface... (4 Replies)
Discussion started by: hassan2
4 Replies
6. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
7. Programming
Hello,
here's my situation: I have a C++ server running on a well known machine and a number of Java clients running on other machines (assumed as unknown) on the same LAN. What I want to achieve is full duplex communication between those applications, in order to exchange complex objects and data... (3 Replies)
Discussion started by: demerzel3
3 Replies
8. Red Hat
Hi all,
I've changed eth0 to (#ethtool eth0):
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
and (#cat /etc/sysconfig/network-scripts/ifcfg-eth):
ETHTOOL_OPTS="autoneg off speed 1000... (3 Replies)
Discussion started by: faraaris
3 Replies
9. UNIX for Advanced & Expert Users
Hi,
I have been trying to connect two computers directly through their LAN cards. One is a 3com 3c905c 10/100 Mbit/s card and the other is an Intel i217-lm 10/100/1000Mbit/s card. I have connected them through a CAT 6 cable. Whenever autoneg is turned on, the PCs connect in the 10Mb/s mode, and... (7 Replies)
Discussion started by: jamie_123
7 Replies
ET(4) BSD Kernel Interfaces Manual ET(4)
NAME
et -- Agere ET1310 10/100/Gigabit Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device et
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_et_load="YES"
DESCRIPTION
The et driver supports PCI Express Ethernet adapters based on the Agere ET1310 chip.
The et driver supports the following media types:
autoselect Enable autoselection of the media types and options. The user can manually override the autoselected mode by adding media
options to the /etc/rc.conf file.
10baseT/UTP Set 10Mbps operation. The mediaopt option can also be used to select either full-duplex or half-duplex modes.
100baseTX Set 100Mbps (Fast Ethernet) operation. The mediaopt option can also be used to select either full-duplex or half-duplex modes.
1000baseT Set 1000Mbps (Gigabit Ethernet) operation. The mediaopt option can only be set to full-duplex mode.
The et driver supports the following media options:
full-duplex Force full-duplex operation.
half-duplex Force half-duplex operation.
Note that the 1000baseT media type is only available if it is supported by the adapter. For more information on configuring this device, see
ifconfig(8).
TUNABLES
hw.et.rx_intr_npkts This value controls how many packets should be received before a receive interrupt is generated. The default value is
32. It is recommended to set this value above 38 to prevent the host from being livelocked under a high degree of
stress.
hw.et.rx_intr_delay This value delays the generation of receive interrupts in units of ~4 microseconds. It is used together with
hw.et.rx_intr_npkts to achieve RX interrupt moderation. The default value is 20.
hw.et.tx_intr_nsegs This value controls how many segments (not packets) should be transmitted before a transmit interrupt is generated. The
default value is 126. It is recommended to set this value below 280 to prevent the TX ring from underflowing.
hw.et.timer This value controls how often a timer interrupt should be generated. It is used together with hw.et.tx_intr_nsegs to
achieve TX interrupt moderation. The default value is 1000000000 (nanoseconds).
SEE ALSO
arp(4), miibus(4), netintro(4), ng_ether(4), vlan(4), ifconfig(8)
HISTORY
The et device driver first appeared in DragonFly 1.11. The first FreeBSD release to include it was FreeBSD 8.0.
AUTHORS
The et driver was written by Sepherosa Ziehau <sepherosa@gmail.com> for DragonFly. It was ported to FreeBSD by Xin LI <delphij@FreeBSD.org>.
BSD
July 14, 2008 BSD