05-11-2009
It seems that the XSCF is dead. For M3000, the XSCF does not come as a separate unit and it is an integrated part of the system board. Need to replace the system board to overcome this
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
there is a message crc error when i install rethat 7.1
what is these message means ?
And why is my harddisk drive detected as hdc not hda ??
please do reply if you have any idea or guesses .
thanking you all
systen config :
intel P4
intel 845
256 SD
... (1 Reply)
Discussion started by: immanuelgangte
1 Replies
2. Solaris
I am getting this error when trying to unzip a file.gz . Anyone know how to resolve this ? (3 Replies)
Discussion started by: jxh461
3 Replies
3. Programming
Hi,
We have packet of size 144 bytes and wants to genrate & check CRC . Can u give the CRC code ? (3 Replies)
Discussion started by: namrata5
3 Replies
4. Solaris
After issuing reboot command (and disconnected from PuTTY), server is not even rebooted because ping test is succesful. So I connect to ALOM and issue poweroff command. After a minute, I did poweron and get this message (only).
rsc> poweron
Are you sure you want to turn your system power on... (10 Replies)
Discussion started by: Olli.Lang
10 Replies
5. Solaris
Hi guys. I have an old Netra T1 that I'm hoping to recover here so I can twiddle around with Solaris 10.
It's been unable to power on despite issuing the "poweron" command or hitting the switch at the back of the server for some time. The LOM command "env" reports ALARM3 ON and everything else... (8 Replies)
Discussion started by: detach8
8 Replies
6. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
7. Shell Programming and Scripting
Hi Forum.
I was trying to search the following scenario on the forum but was not able to.
Let's say that I have a very large file that has some bad data in it (for ex: 0.0015 in the 12th column) and I would like to find the line number and remove that particular line.
What's the easiest... (3 Replies)
Discussion started by: pchang
3 Replies
8. Solaris
Hi,
I've updated a few M3000s to new firmware without any hassle, but on one of them the following is happening:
XSCF> getflashimage -u wayner ftp://10.16.122.200/tftpboot/IKXCP1102.tar.gz
Error: insufficient free space
Any idea how to delete whatever old firmware is on there so I can... (7 Replies)
Discussion started by: cabaiste
7 Replies
9. Emergency UNIX and Linux Support
we have a SUN M3000 server.
setup as only 1 domain.
disk c0t0d0 and c0t1d0 and setup as SVM mirrors.
a few days ago disk T1 failed.
new we have replaced the disk, but can's see the disk in format.
have done cfgadm and devfsadm.
still can't access the new disk in format.
the output... (6 Replies)
Discussion started by: robsonde
6 Replies
10. Solaris
Hi
We have an M3000 single physical processor and 8gb of memory running Solaris 10. This system runs two Oracle Databases one on Oracle 9i and One on Oracle 10g.
As soon as the Oracle 10g database starts we see an immediate drop in system performance, for example opening an ssh session can... (6 Replies)
Discussion started by: gregsih
6 Replies
LEARN ABOUT DEBIAN
freecell-solver-range-parallel-solve
HOOLA(6) Freecell Solver HOOLA(6)
NAME
freecell-solver-range-parallel-solve - The Freecell Solver utility for solving a range of Microsoft Freecell/Freecell Pro Boards
SYNOPSIS
freecell-solver-range-parallel-solve start end print_step [--binary-output-to filename] [--total-iterations-limit limit] [fc-solve
Arguments...]
DESCRIPTION
freecell-solver-range-parallel-solve is a command line application that solves a range of Freecell deals of Microsoft Freecell and Freecell
Pro.
start is the first board to solve; end is the last (inclusive) and print_step is the division of board numbers in which to print a status
message.
Following this three mandatory parameters are several flags specific to the range solve. (refer to the OPTIONS section for more
information)
Afterwards one can give it a fc-solve command line that it will use to solve each board. Refer to the fc-solve(6) man page for information
about its options.
OPTIONS
--total-iterations-limit sets the maximal number of iterations with which to try to solve each deal. After that, the program will give up
and report that the board was intractable.
--binary-output-to sets the filename into which to output the number of iterations it took to solve each board. This file can later be used
with statistical preset optimizers such as those found in the Freecell Solver version control repository.
SEE ALSO
fc-solve(6)
AUTHOR
Shlomi Fish, <http://www.shlomifish.org/> .
Freecell Solver 3.12.0 2012-06-22 HOOLA(6)