Sponsored Content
Operating Systems Solaris Can't PowerOn M3000 - Bad Data CRC Post 302314940 by incredible on Monday 11th of May 2009 05:26:34 AM
Old 05-11-2009
It seems that the XSCF is dead. For M3000, the XSCF does not come as a separate unit and it is an integrated part of the system board. Need to replace the system board to overcome this
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

crc error ? ? ? ? H E L P

there is a message crc error when i install rethat 7.1 what is these message means ? And why is my harddisk drive detected as hdc not hda ?? please do reply if you have any idea or guesses . thanking you all systen config : intel P4 intel 845 256 SD ... (1 Reply)
Discussion started by: immanuelgangte
1 Replies

2. Solaris

invalid compressed data--crc error

I am getting this error when trying to unzip a file.gz . Anyone know how to resolve this ? (3 Replies)
Discussion started by: jxh461
3 Replies

3. Programming

CRC Code

Hi, We have packet of size 144 bytes and wants to genrate & check CRC . Can u give the CRC code ? (3 Replies)
Discussion started by: namrata5
3 Replies

4. Solaris

V490 Failed To Boot After ALOM poweron

After issuing reboot command (and disconnected from PuTTY), server is not even rebooted because ping test is succesful. So I connect to ALOM and issue poweroff command. After a minute, I did poweron and get this message (only). rsc> poweron Are you sure you want to turn your system power on... (10 Replies)
Discussion started by: Olli.Lang
10 Replies

5. Solaris

Sun Netra T1 won't poweron/no POST

Hi guys. I have an old Netra T1 that I'm hoping to recover here so I can twiddle around with Solaris 10. It's been unable to power on despite issuing the "poweron" command or hitting the switch at the back of the server for some time. The LOM command "env" reports ALARM3 ON and everything else... (8 Replies)
Discussion started by: detach8
8 Replies

6. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS (4 Replies)
Discussion started by: rajasekg
4 Replies

7. Shell Programming and Scripting

Find line number of bad data in large file

Hi Forum. I was trying to search the following scenario on the forum but was not able to. Let's say that I have a very large file that has some bad data in it (for ex: 0.0015 in the 12th column) and I would like to find the line number and remove that particular line. What's the easiest... (3 Replies)
Discussion started by: pchang
3 Replies

8. Solaris

XSCF on M3000

Hi, I've updated a few M3000s to new firmware without any hassle, but on one of them the following is happening: XSCF> getflashimage -u wayner ftp://10.16.122.200/tftpboot/IKXCP1102.tar.gz Error: insufficient free space Any idea how to delete whatever old firmware is on there so I can... (7 Replies)
Discussion started by: cabaiste
7 Replies

9. Emergency UNIX and Linux Support

disk replacment, SUN M3000

we have a SUN M3000 server. setup as only 1 domain. disk c0t0d0 and c0t1d0 and setup as SVM mirrors. a few days ago disk T1 failed. new we have replaced the disk, but can's see the disk in format. have done cfgadm and devfsadm. still can't access the new disk in format. the output... (6 Replies)
Discussion started by: robsonde
6 Replies

10. Solaris

Poor performance on an M3000

Hi We have an M3000 single physical processor and 8gb of memory running Solaris 10. This system runs two Oracle Databases one on Oracle 9i and One on Oracle 10g. As soon as the Oracle 10g database starts we see an immediate drop in system performance, for example opening an ssh session can... (6 Replies)
Discussion started by: gregsih
6 Replies
SULOGIN(8)						       System Administration							SULOGIN(8)

NAME
sulogin - Single-user login SYNOPSIS
sulogin [options] [tty] DESCRIPTION
sulogin is invoked by init when the system goes into single user mode. The user is prompted: Give root password for system maintenance (or type Control-D for normal startup): sulogin will be connected to the current terminal, or to the optional tty device that can be specified on the command line (typically /dev/console). After the user exits the single-user shell or presses control-D at the prompt, the system will continue to boot. OPTIONS
-e, --force If the default method of obtaining the root password via getpwnam(3) from the system fails, manually examine /etc/passwd and /etc/shadow to get the password. If they are damaged or nonexistent, sulogin will start a root shell without asking for a password. Only use the -e option if you are sure the console is physically protected against unauthorized access. -p, --login-shell Specifying this option causes sulogin to start the shell process as a login shell. -t, --timeout seconds Specify the maximum amount of time to wait for user input. By default, sulogin will wait forever. -h, --help Print a help message. -V, --version Output version. ENVIRONMENT VARIABLES
sulogin looks for the environment variable SUSHELL or sushell to determine what shell to start. If the environment variable is not set, it will try to execute root's shell from /etc/passwd. If that fails it will fall back to /bin/sh. AUTHOR
sulogin was written by Miquel van Smoorenburg for sysvinit and later ported to util-linux by Dave Reisner and Karel Zak. AVAILABILITY
The sulogin command is part of the util-linux package and is available from Linux Kernel Archive <ftp://ftp.kernel.org/pub/linux/utils /util-linux/>. util-linux Jul 2012 SULOGIN(8)
All times are GMT -4. The time now is 08:02 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy