05-07-2009
You asked a similar question recently but it was not clear then whether you were running a unix/Linux emulator under Windows XP or a normal bootable unix/Linux.
Please clarify what exactly Operating System and version you are running and on what platform.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error.
Any suggestions (2 Replies)
Discussion started by: macdonto
2 Replies
2. UNIX for Dummies Questions & Answers
Hello,
hi guys I don't know what is the problem with my NIC I can ping the Localhost (LOOPBACK) but when I run a scripts to check the NIC statuse it's shown the NIC DOWN sooo what could be the problem and what is the best way to start trouplshooting the NIC in SUN-SOLARIS.
Regards,
Karim
... (3 Replies)
Discussion started by: geoquest
3 Replies
3. Shell Programming and Scripting
Hi can someone tell me what command i can use to find the NIC status im using the bash shell. I'v tried ifconfig -a but this comes back as command not found. (3 Replies)
Discussion started by: warlock129
3 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Solaris
Hi guys,
Another problem here and I appreciate the help,
the interface in the solaris v440 is showing as "FAILED"
ce0: flags=19040803<UP,BROADCAST,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,FAILED> mtu 1500 index 2
inet 192.168.1.30 netmask ffffff00 broadcast 192.168.1.255
... (14 Replies)
Discussion started by: br1an
14 Replies
8. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
9. Programming
Dear Team
I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update )
Scenario
We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted... (1 Reply)
Discussion started by: Perlbaby
1 Replies
PCCARD(4) BSD Kernel Interfaces Manual PCCARD(4)
NAME
pccard -- PC Card bus driver
SYNOPSIS
device pccard
DESCRIPTION
The pccard driver implements the PC Card bus. The pccard driver supports all PC Card bridges in the system.
TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command:
hw.pccard.debug Non-zero values cause more verbose information to be printed when a 16-bit PC Card is inserted or removed.
hw.pccard.cis_debug Non-zero value causes the CIS parsing of the 16-bit PC Card to be much more verbose and include a complete CIS dump.
FILES
/dev/pccard0.cis This exclusive-use device will report all the CIS chains present in a PC Card, if a 16-bit PC Card is inserted in the slot.
Only one user at a time may access the CIS. The CIS is presented as the relevant byte stream from the PC Card. For CIS
tuples in Attribute Memory (the default), only the even locations are presented (the ODD locations are undefined per the
standard). For CIS tuples in Common Memory, every byte is presented to the user. Decoding of the CIS tuples is done via a
userland program. All tuples are presented to the user.
SEE ALSO
cardbus(4), pccbb(4)
PC Card Standard, Release 8.
BSD
July 9, 2002 BSD