05-07-2009
ifconfig
Did you consider to search the forums before asking such basic question?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error.
Any suggestions (2 Replies)
Discussion started by: macdonto
2 Replies
2. UNIX for Dummies Questions & Answers
Hello,
hi guys I don't know what is the problem with my NIC I can ping the Localhost (LOOPBACK) but when I run a scripts to check the NIC statuse it's shown the NIC DOWN sooo what could be the problem and what is the best way to start trouplshooting the NIC in SUN-SOLARIS.
Regards,
Karim
... (3 Replies)
Discussion started by: geoquest
3 Replies
3. Shell Programming and Scripting
Hi can someone tell me what command i can use to find the NIC status im using the bash shell. I'v tried ifconfig -a but this comes back as command not found. (3 Replies)
Discussion started by: warlock129
3 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Solaris
Hi guys,
Another problem here and I appreciate the help,
the interface in the solaris v440 is showing as "FAILED"
ce0: flags=19040803<UP,BROADCAST,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,FAILED> mtu 1500 index 2
inet 192.168.1.30 netmask ffffff00 broadcast 192.168.1.255
... (14 Replies)
Discussion started by: br1an
14 Replies
8. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
9. Programming
Dear Team
I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update )
Scenario
We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted... (1 Reply)
Discussion started by: Perlbaby
1 Replies
LEARN ABOUT DEBIAN
if_edsc
EDSC(4) BSD Kernel Interfaces Manual EDSC(4)
NAME
edsc -- Ethernet discard network interface
SYNOPSIS
device edsc
DESCRIPTION
The edsc interface is a software discard mechanism which may be used for performance analysis and software testing. It imitates an Ethernet
device, which allows for its use in conjunction with such drivers as if_bridge(4) and vlan(4).
As with other network interfaces, an edsc interface must have network addresses assigned for each address family with which it is to be used.
These addresses may be set or changed with the SIOCSIFADDR ioctl(2) or ifconfig(8) utility.
Each edsc interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the
cloned_interfaces variable in rc.conf(5).
SEE ALSO
ioctl(2), arp(4), if_bridge(4), inet(4), intro(4), vlan(4), rc.conf(5), arp(8), ifconfig(8)
HISTORY
The edsc device was derived from the disc(4) device and first appeared in FreeBSD 6.3. This manpage was adapted from disc(4).
CAVEATS
Since outgoing packets are just discarded by edsc, ARP requests stay unreplied. Consequently, an IP packet cannot be sent via edsc until a
static arp(4) entry is created for its next hop using arp(8).
Initially an edsc interface has a zero link level address. It can be changed with ifconfig(8) lladdr if needed.
BSD
March 25, 2007 BSD