I have a services file configured in /etc in there windows clients connect to my server on port 6034-6037
when I do the following
it pulls all the connections active for those ports
so right now I have 10 clients connected but posted only 3
I need to kill only these ESTABLISHED clients that relate to these ports only
I did the following
and
I hoped this would set the interval to send a reset at 800ms or lessen the keep alive but the connections are still there as ESTABLISHED. Am I looking at this the wrong way or what I am trying to do is not what i posted.
Please help to point me in the right direction this is sort of affecting out class
Last edited by deaconf19; 05-06-2009 at 08:21 AM..
I am trying to set an interface to 100/Full, but the command I use are getting rejected. I think it is the last argument, but I don't know how to find the correct values.
I am trying to use the following script, but change hme to le .
echo "Setting hme interface 1: 100mb/full-duplex..."
... (2 Replies)
Hi Guys,
I need help with ndd.
I was going through network FAQ but i have more questions then answers regarding ndd.
#ndd -set /dev/hme instance 0
#ndd -set /dev/hme adv_100fdx_cap 1
#ndd -set /dev/hme adv_100hdx_cap 0
#ndd -set /dev/hme adv_10fdx_cap 0
#ndd -set /dev/hme adv_10hdx_cap 0... (2 Replies)
Hi, Anyone can help
My solaris 8 system has the following
/dev/null , /dev/tty and /dev/console
All permission are lrwxrwxrwx
Can this be change to a non-world write ??
any impact ?? (12 Replies)
Hi,
I would like to know whether there is any config file that i can refer to for the result of 'ndd -get /dev/tcp tcp_time_wait_interval'?
When i man 'ndd', there is one statement which is -> Each driver chooses which parameters to make visible using ndd. Does it answering my question above... (3 Replies)
While in SCO Openserver 5.0.7, Sybase listened to /dev/inet/tcp, the same is not working in SCO Openserver 6. The Network card is however active and pinging fine. What can be the reason? What is the way out?
An early response will be appreciated.
Thank you
Regards
TCG (2 Replies)
Following command was set up in startup script on Solaris 8 servers - improved network transfers of files from one server to the another (doubled transfer speed).
ndd -set /dev/tcp tcp_host_param '10.140.20.10 sendspace 279600 recvspace 279600 timestamp 1'
Now they are getting a new server... (15 Replies)
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
I have problem with oracle solaris 10 running on oracle sparc T4-2 server.
Os information: 5.10 Generic_150400-03 sun4v sparc sun4v
Output from tcpstat.d script
TCP bytes: out outRetrans in inDup inUnorder
6833763 7300 98884 0... (2 Replies)
Objective: To recreate the partitioning setup of /dev/sda on /dev/sdc
How would I parse the below information and initialize variables
(an array?) that can be used to build sgdisk commands in a script, regardless of the number of partitions?
Something along the lines of:
sgdisk -n... (12 Replies)
I have a command to check the status of hostname and port number,
echo > /dev/tcp/hostname/80
echo $?
0
success case
echo > /dev/tcp/hostname/809999
I got the output
-------------------
connection timed out
It took almost 4 minutes to time out,,, how can I set it to 10 seconds?
my... (2 Replies)
Discussion started by: sam@sam
2 Replies
LEARN ABOUT OSX
ndd
ndd(1M) System Administration Commands ndd(1M)NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)