|
|
Sponsored Content
Operating Systems
Solaris
SF T2000 prtdiag problem
Post 302312995 by pupp on Monday 4th of May 2009 10:29:42 AM
05-04-2009
incredible - i know of some similar issues regarding hardware query commands that either crashed a system or hung up the session. picl seemed to have restored order but patches were applied as this was recommended by sun. whether these were patches applied directly from sun or from a latest cluster, i'm not sure.
i think you should open up another case with sun as i think this is a code issue and nothing much we can do to help. until then, maybe a cron of /usr/platform/`uname -i`/sbin/prtdiag can help you along the way. run it once a day or maybe twice... see if you can get at least 1 of the 2 good outputs.
just me typing out out loud
i'm wondering if prtpicl shows different output from a good prtdiag result versus a bad prtdiag result.
i think you should open up another case with sun as i think this is a code issue and nothing much we can do to help. until then, maybe a cron of /usr/platform/`uname -i`/sbin/prtdiag can help you along the way. run it once a day or maybe twice... see if you can get at least 1 of the 2 good outputs.
just me typing out out loud
i'm wondering if prtpicl shows different output from a good prtdiag result versus a bad prtdiag result.
Last edited by pupp; 05-04-2009 at 11:36 AM..
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello all ,
This is the output of my prtdiag command ...The speed of each of the CPUs is listed below (1281 MHz ) ..That's fine ..I'm confused about the (System clock frequency: 183 MHZ ) ..What is the difference between System Clock freq and CPU freq ...THanks..
System Configuration: Sun... (5 Replies)
Discussion started by: luft
5 Replies
2. Solaris
Hi everyone,
I am having a problem when running devfsadm. We have many T2000, but on one of them, that is connected to our SAN, devfsadm reports no new disks. If a reconfiguration reboot is done, the system reports the new disk. But only with a reboot. We have Solaris10 installed and Veritas... (13 Replies)
Discussion started by: jfotop
13 Replies
3. Solaris
Hi,
I have a netra t2000 running solaris 10. It is fully patched with the latest patch cluster and also patch 118833-36 and 126897-02. The SC sys_event level is set to 3.
I am running a test to show hardware log status, e.g simulating a power supply failure.Hence I unplug one of te... (3 Replies)
Discussion started by: ulemsee
3 Replies
4. UNIX for Advanced & Expert Users
Dear All....Help required
prtdiag -v command shows no output on my V440 server.
Following is the details:
root@sdp16b>prtdiag -v
root@sdp16b>
root@sdp16b>uname -a
SunOS sdp16b 5.9 Generic_122300-31 sun4u sparc SUNW,Sun-Fire-V440
root@sdp16b>echo $path
/usr/sbin /usr/bin /usr/sbin... (6 Replies)
Discussion started by: Junaid
6 Replies
5. Solaris
Hi All
I have a problem on T2000 server.
bash-3.00# uname -a
SunOS 5.10 aaa Generic_120011-14 sun4v sparc SUNW,Netra-T2000After the initial solaris installation server failed to boot:
Rebooting with command: boot
Boot device: disk:b File and args:
The file just loaded does not appear... (1 Reply)
Discussion started by: ouzist
1 Replies
6. Solaris
Hi all,
First post so be gentile :)
It's my first time installing Solaris on T2000 server.
I have 2 72GB HD's on it.
After configuring HW raid and running raidctl command I get this output:
bash-3.00# raidctl -l c0t0d0
Volume Size Stripe Status Cache RAID
... (2 Replies)
Discussion started by: Obi-Wan
2 Replies
7. Solaris
hi all
when i trying to give auto-boot value as false as following
#eeprom auto-boot?=false
it is showing as
zsh: no matches found: auto-boot?=false
so felt this is because of error in hard ware so i tried this
#iostat -en
it is showing like
iostat -en
---- errors ---
s/w h/w trn... (4 Replies)
Discussion started by: wkbn86
4 Replies
8. UNIX for Advanced & Expert Users
Hi Friends,
I need a help from you all.
In my machine which is on Solaris 9.
the command prtdiag -v shows the complete output but it doesn't show "Memory Module Groups status" status.
I have tried restarting the picl daemon, but still it doesn't work.
Memory Module Groups:... (2 Replies)
Discussion started by: vivek.goel.piet
2 Replies
9. Solaris
Hi everyone,
Please can you tell me what kind of memro we are talking about when we run :
prtdiag -v
Memory size: 98016 Megabytes
Thank you (7 Replies)
Discussion started by: adilyos
7 Replies
10. Solaris
selected lines from the output of the "prtdiag -v" command on a T5240 SUN server running Solaris 10.
Are the following known as FRU names and what do they mean?
MB/CMP0/BR0/CH0/D0
MB/CMP0/BR0/CH1/D0
SYS/FANBD0/FM0/F0
SYS/FANBD0/FM0/F1
SYS/MB/CMP0/BR1/CH0/D1 ... (1 Reply)
Discussion started by: snoman1
1 Replies
LEARN ABOUT REDHAT
what-patch
WHAT-PATCH(1) General Commands Manual WHAT-PATCH(1) NAME
what-patch - detect which patch system a Debian package uses SYNOPSIS
what-patch [options] DESCRIPTION
what-patch examines the debian/rules file to determine which patch system the Debian package is using. what-patch should be run from the root directory of the Debian source package. OPTIONS
Listed below are the command line options for what-patch: -h, --help Display a help message and exit. -v Enable verbose mode. This will include the listing of any files modified outside or the debian/ directory and report any additional details about the patch system if available. AUTHORS
what-patch was written by Kees Cook <kees@ubuntu.com>, Siegfried-A. Gevatter <rainct@ubuntu.com>, and Daniel Hahler <ubuntu@thequod.de>, among others. This manual page was written by Jonathan Patrick Davies <jpds@ubuntu.com>. Both are released under the GNU General Public License, version 3 or later. SEE ALSO
The Ubuntu MOTU team has some documentation about patch systems at the Ubuntu wiki: https://wiki.ubuntu.com/PackagingGuide/PatchSystems cdbs-edit-patch(1), dbs-edit-patch(1), dpatch-edit-patch(1) DEBIAN
Debian Utilities WHAT-PATCH(1)