BIOS Serial Number on Sun Fire V240 Post: 302310248

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Help: Sun Disk partitioning for Sun V240 & StorEdge 3300

Dear Sun gurus, I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document...

2. Solaris

connecting laptop to V240 serial port

Well...I hope I am in the right forum to post this question. Here is what I am trying to do. I have a laptop (Dell I believe) running Windows. I am trying to connect this laptop to a V240 serial port (the port with l0l0l). Here lies the problem, I am not sure if I have the correct cable. I do...

3. Solaris

Sun 280r serial number

is there a command i can run at the ksh that will give me the serial number on solaris? solaris 8, and 9 280r servers

4. Solaris

Sun Fire 280R Sun Solaris CRT/Monitor requirements

I am new to Sun. I brought Sun Fire 280R to practice UNIX. What are the requirements for the monitor/CRT? Will it burn out old non-Sun CRTs? Does it need LCD monitor? Thanks.

5. Solaris

Sun Fire V890 - Unable to access RSC or Serial console

Hello Folks, I am having trouble to login to rsc or serial console of V890. The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting...

6. Solaris

Alom Sun V240

hallo anybody know how to set alom mail alerty server with yahoomail ? thank u?where i can find mail server address for yahoomail?thank

7. Red Hat

CLI for serial number or tag for BIOS

what file or command can be used to get information that can represent unique ID for BIOS installed, it could be serial number or some tag. I used "/usr/sbin/dmidecode | egrep -i 'BIOS Information' -A 20" command, it shows some information about BIOS but not some information that can be used as...

8. Hardware

Sun fire 4270 reset BIOS settings after reboot

Hello, I am trying to perform Suse 10 SP3 installation via network in 6 Sun Fire 4270 M2 servers. The problem is that even if i set first prio boot device the hard disk the system always try to boot from network.And after the first restart the BIOS setting has been lost(and PXE come first...

9. Solaris

Sun Fire V240 server Fan replacement

I have a sun fire v240 server. The output of prtdiag -v shows a failed fan. There are 3 fans for cooling system board. There is 1 fan for each of the powersupply (There are 2 powersupplies) From the below output how do i know which fan is bad and whats its location...

LEARN ABOUT OPENSOLARIS

sparc

machid(1)							   User Commands							 machid(1)

NAME

       machid, sun, iAPX286, i286, i386, i486, i860, pdp11, sparc, u3b, u3b2, u3b5, u3b15, vax, u370 - get processor type truth value

SYNOPSIS

       sun

       iAPX286

       i386

       pdp11

       sparc

       u3b

       u3b2

       u3b5

       u3b15

       vax

       u370

DESCRIPTION

       The following commands will return a true value (exit code of 0) if you are using an instruction set that the command name indicates.

       sun	  True if you are on a Sun system.

       iAPX286	  True if you are on a computer using an iAPX286 processor.

       i386	  True if you are on a computer using an iAPX386 processor.

       pdp11	   True if you are on a PDP-11/45tm or PDP-11/70tm.

       sparc	  True if you are on a computer using a SPARC-family processor.

       u3b	  True if you are on a 3B20 computer.

       u3b2	  True if you are on a 3B2 computer.

       u3b5	  True if you are on a 3B5 computer.

       u3b15	  True if you are on a 3B15 computer.

       vax	  True if you are on a VAX-11/750tm or VAX-11/780tm.

       u370	  True if you are on an IBM(R) System/370tm computer.

       The  commands  that  do	not  apply will return a false (non-zero) value. These commands are often used within makefiles (see make(1S)) and
       shell scripts (see sh(1)) to increase portability.

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcsu			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       make(1S), sh(1), test(1), true(1), uname(1), attributes(5)

NOTES

       The machid family of commands is obsolete. Use uname -p and uname -m instead.

SunOS 5.11							    5 Jul 1990								 machid(1)