04-24-2009
Quote:
Originally Posted by
vineetd
Hi,
I want to know if there is a command available for obtaining the BIOS Serial Number on a Sun Fire V240 machine? Or is it a known issue that it cannot be obtained through any command?
Thanks,
Vineet
on the older V240's you have to eyeball the box and see the serial number sticker.
on most of the newer boxes (last 12-18 months) it is in the NVRAM and can be seen using sneep.
sneep can be installed from a solaris package.
if you have an older box, you can use sneep to put the serial number into NVRAM.
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Sun gurus,
I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Discussion started by: shafeeq
1 Replies
2. Solaris
Well...I hope I am in the right forum to post this question. Here is what I am trying to do.
I have a laptop (Dell I believe) running Windows. I am trying to connect this laptop to a V240 serial port (the port with l0l0l). Here lies the problem, I am not sure if I have the correct cable. I do... (6 Replies)
Discussion started by: bluridge
6 Replies
3. Solaris
is there a command i can run at the ksh that will give me the serial number on solaris?
solaris 8, and 9
280r servers (16 Replies)
Discussion started by: BG_JrAdmin
16 Replies
4. Solaris
I am new to Sun.
I brought Sun Fire 280R to practice UNIX. What are the requirements for the monitor/CRT? Will it burn out old non-Sun CRTs? Does it need LCD monitor?
Thanks. (3 Replies)
Discussion started by: bramptonmt
3 Replies
5. Solaris
Hello Folks,
I am having trouble to login to rsc or serial console of V890.
The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
Discussion started by: defflepord
8 Replies
6. Solaris
hallo anybody know how to set alom mail alerty server with yahoomail ?
thank u?where i can find mail server address for yahoomail?thank (1 Reply)
Discussion started by: yanto85
1 Replies
7. Red Hat
what file or command can be used to get information that can represent unique ID for BIOS installed, it could be serial number or some tag.
I used "/usr/sbin/dmidecode | egrep -i 'BIOS Information' -A 20" command, it shows some information about BIOS but not some information that can be used as... (4 Replies)
Discussion started by: epriya2003
4 Replies
8. Hardware
Hello,
I am trying to perform Suse 10 SP3 installation via network in 6 Sun Fire 4270 M2 servers.
The problem is that even if i set first prio boot device the hard disk the system always try to boot from network.And after the first restart the BIOS setting has been lost(and PXE come first... (2 Replies)
Discussion started by: @dagio
2 Replies
9. Solaris
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
cvcd(1M) System Administration Commands cvcd(1M)
NAME
cvcd - virtual console daemon
SYNOPSIS
/platform/platform_name/cvcd
DESCRIPTION
The virtual console daemon, cvcd, is a server process that supports the network console provided on some platforms. The cvcd daemon accepts
network console connections from a remote host (only one host at any given time). Console input is read from this connection and forwarded
to cvc(7D) by way of cvcredir(7D).
Similarly, console output is read from cvcredir(7D) and forwarded across the network console connection. If cvcd dies, console traffic is
automatically rerouted through an internal hardware interface.
The cvcd daemon normally starts at system boot time. Each domain supports only one cvcd process at a time.
Caution: On Sun Enterprise 10000 domains, cvcd uses a configuration file (/etc/ssphostname) to determine the name of the host from
which network console connections are allowed. If the remote console host is renamed, you must edit the configuration file
to reflect that change.
OPERANDS
The following operands are supported:
platform_name The official Sun platform name used in packaging and code. For example, for Sun Fire 15K servers, the platform_name
would be SUNW,Sun-Fire-15000.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |Sun Enterprise 10000 |
| |servers, Sun Fire High-End |
| |Systems |
+-----------------------------+-----------------------------+
|Availability |SUNWcvc.u |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1), svcadm(1M), services(4), attributes(5), smf(5), cvc(7D), cvcredir(7D)
Sun Enterprise 10000 SSP Reference Manual
System Management Services (SMS) Reference Manual
NOTES
The cvcd service is managed by the service management facility, smf(5), under the service identifier:
svc:/system/cvc
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
SunOS 5.10 11 Aug 2004 cvcd(1M)