04-22-2009
10 More Discussions You Might Find Interesting
1. HP-UX
Using HP-UX v11
Need to monitor cpu and memory usage, total for system and separately for each user in command-line mode.
Found out next ways to monitor total cpu usage under hp-ux:
1) vmstat, also shows free memory
2) sar -M
ps -eo user,pcpu - does not work, means 'user-defined format'... (4 Replies)
Discussion started by: hp-ux-user
4 Replies
2. HP-UX
how can I find cpu usage memory usage swap usage and
I want to know CPU usage above X% and contiue Y times and memory usage above X % and contiue Y times
my final destination is monitor process
logical volume usage above X % and number of Logical voluage above
can I not to... (3 Replies)
Discussion started by: alert0919
3 Replies
3. Solaris
Hi,
Im working on Solaris 9 on SPARC-32 bit running on an Ultra-80, and I have to find out the following:-
1. Total Physical Memory in the system(total RAM).
2. Available Physical Memory(i.e. RAM Usage)
3. Total (Logical) Memory in the system
4. Available (Logical) Memory.
I know... (4 Replies)
Discussion started by: 0ktalmagik
4 Replies
4. AIX
How to monitor the IBM AIX server for I/O usage, memory usage, CPU usage, network usage, storage usage? (3 Replies)
Discussion started by: laknar
3 Replies
5. UNIX for Dummies Questions & Answers
HI guys,
:confused:i would like to know how can i determine
the total/approx memory used by a single user. Example Top output is below
===========================================================================
top - 20:00:50 up 24 days, 2:48, 2 users, load average: 0.43, 0.40, 0.37... (3 Replies)
Discussion started by: cromohawk
3 Replies
6. UNIX for Dummies Questions & Answers
Hi all,
Is it possible to get total memory usage and free memory usage without top? By Googling I found for total memory usage, use vmstat, for CPU, use mpstat, for disk I/O use iostat, is this correct? Will using sar gives the same result as ALL of these three (3) commands?
What about if I... (2 Replies)
Discussion started by: newbie_01
2 Replies
7. UNIX for Dummies Questions & Answers
Hi all
Can anyone advise/confirm whether total CPU usage when running sar is %user+%system+%iowait or is it %user+%system only?
I want to confirm whether I am having a CPU-bound problem or not.
This is a single-CPU VMware machine.
$ sar 5 20
Linux 2.6.18-238.5.1.el5... (7 Replies)
Discussion started by: newbie_01
7 Replies
8. UNIX for Advanced & Expert Users
Hi,
I have a server box with 16GB ram in it, within the server box there are 3 VMs running with a total allocation of 9GB.
if I add up all the numbers under memory info using vmstat I get 15.8GB so I can say it adds up to 16Gb...
Is there a way to see from the command line how much memory... (2 Replies)
Discussion started by: speedhunt3r
2 Replies
9. Solaris
Hello All
I have a Solaris 10 machine, wherein processes are run in various unix users.
a. How do I list the memory usage per user?
b. Can I get a top command kind of output per user rather than entire machine?
Thanks
Sunil Kumar (3 Replies)
Discussion started by: msgforsunil
3 Replies
10. UNIX for Dummies Questions & Answers
Let's say i have 20 users logged on Server. How can I know how much memory percent used each of them is using with system time in each user? (2 Replies)
Discussion started by: roy1912
2 Replies
LEARN ABOUT REDHAT
netdump
NETDUMP-CLIENT(8) System Programs NETDUMP-CLIENT(8)
NAME
netdump - send oops data and memory dumps over the network
SYNOPSIS
/etc/init.d/netdump (start|stop|status|restart|propagate)
DESCRIPTION
Loads and configures the netdump kernel modules. Once these are loaded, when the kernel crashes it will send the oops message and a dump of
physical memory to the machine that runs the netdump-server. This can then be used to debug the problem using gdb and a kernel image.
OPTIONS
start Starts the netdump client service. Loads the kernel modules with the right options.
stop Unloads the kernel modules.
status Shows the status of the netdump client
restart
Restarts the netclient modules with new configurations.
propagate
Sends the ssh public key needed to update the random key for each netdump session to the netdump server.
FILES
/etc/sysconfig/netdump
Configuration for the netdump client. You need to at least specify the address of the machine running the netdump server here.
/etc/sysconfig/netdump_id_dsa.pub
Public key for this machine. Used by the server to authenticate the client. This must be installed on the server, possibly by using
the the propagate capability of the netdump init script, which does:
cat /etc/sysconfig/netdump_id_dsa.pu | ssh netdump@$NETDUMPADDR cat '>>' /var/crash/.ssh/authorized_keys2
Where $NETDUMPADDR is the ip or name of the machine running the netdump server.
SEE ALSO
netdump-server(8), init(8)
BUGS
Report any bugs you find to http://bugzilla.redhat.com/bugzilla
AUTHOR
Alexander Larsson <alexl@redhat.com>
Linux 14 Feb 2002 NETDUMP-CLIENT(8)