Sponsored Content
Full Discussion: T2000 Hardware RAID
Operating Systems Solaris T2000 Hardware RAID Post 302307188 by honmin on Tuesday 14th of April 2009 10:22:36 PM
Old 04-14-2009
T2000 Hardware RAID

Hi,

I have a root with hardware RAID on c0t0d0 and c0t2d0. I would like to set the boot device sequence in OBP for both hdds.

I have checked in ls -l /dev/rdsk/ for the path of c0t2d0 but it does not exist. Can anyone shed some lights on this?


Code:
 
AVAILABLE DISK SELECTIONS:
0. c0t0d0 <LSILOGIC-LogicalVolume-3000 cyl 65533 alt 2 hd 16 sec 273>
/pci@780/pci@0/pci@9/scsi@0/sd@0,0

 

9 More Discussions You Might Find Interesting

1. Solaris

Hardware RAID

I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Discussion started by: jess_t03
7 Replies

2. Solaris

How to setup hardware RAID on a T2000

Hello all We've just bought a T2000. It has two disks and I'm trying to figure out how to create a mirror of the boot disk. I understand that I have to boot into single user mode from DVD and then use the raidctl command to set up the mirror and label the volume afterwards. Format returns... (4 Replies)
Discussion started by: soliberus
4 Replies

3. Solaris

T2000 RAID Question

New to the boards here so please bear with me! I have a T2000 server with Solaris 10 installed on it. Disk 0 is the only disk currently being used, as I do NOT have a RAID set up. Disk 1 is just sitting there looking pretty. I'd like to set up a mirrored RAID in order to fully utilize both... (5 Replies)
Discussion started by: phi148
5 Replies

4. Solaris

Raid problem on T2000

Hi all, First post so be gentile :) It's my first time installing Solaris on T2000 server. I have 2 72GB HD's on it. After configuring HW raid and running raidctl command I get this output: bash-3.00# raidctl -l c0t0d0 Volume Size Stripe Status Cache RAID ... (2 Replies)
Discussion started by: Obi-Wan
2 Replies

5. UNIX for Dummies Questions & Answers

RAID software vs hardware RAID

Hi Can someone tell me what are the differences between software and hardware raid ? thx for help. (2 Replies)
Discussion started by: presul
2 Replies

6. Solaris

Hardware Raid - LiveUpgrade

Hi, I have a question. Do LiveUpgrade supports hardware raid? How to choose the configuration of the system disk for Solaris 10 SPARC? 1st Hardware RAID-1 and UFS 2nd Hardware RAID-1 and ZFS 3rd SVM - UFS and RAID1 4th Software RAID-1 and ZFS I care about this in the future to take... (1 Reply)
Discussion started by: bieszczaders
1 Replies

7. Hardware

Hardware RAID on Sun T2000 Server

Hi All I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command. Following is the hardware RAID output. root@oracledatabaseserver / $ raidctl RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies

8. Hardware

Sun T3-1 hardware RAID

Hi all I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS. The documentation doesn't make it clear if: 1. The... (6 Replies)
Discussion started by: soliberus
6 Replies

9. Solaris

Software RAID on top of Hardware RAID

Server Model: T5120 with 146G x4 disks. OS: Solaris 10 - installed on c1t0d0. Plan to use software raid (veritas volume mgr) on c1t2d0 disk. After format and label the disk, still not able to detect using vxdiskadm. Question: Should I remove the hardware raid on c1t2d0 first? My... (4 Replies)
Discussion started by: KhawHL
4 Replies
MFI(4)							   BSD Kernel Interfaces Manual 						    MFI(4)

NAME
mfi -- LSI MegaRAID SAS driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device pci device mfi Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): mfi_load="YES" DESCRIPTION
This driver is for LSI's next generation PCI Express SAS RAID controllers. Access to RAID arrays (logical disks) from this driver is pro- vided via /dev/mfid? device nodes. A simple management interface is also provided on a per-controller basis via the /dev/mfi? device node. The mfi name is derived from the phrase "MegaRAID Firmware Interface", which is substantially different than the old "MegaRAID" interface and thus requires a new driver. Older SCSI and SATA MegaRAID cards are supported by amr(4) and will not work with this driver. Two sysctls are provided to tune the mfi driver's behavior when a request is made to remove a mounted volume. By default the driver will disallow any requests to remove a mounted volume. If the sysctl dev.mfi.%d.delete_busy_volumes is set to 1, then the driver will allow mounted volumes to be removed. HARDWARE
The mfi driver supports the following hardware: o LSI MegaRAID SAS 1078 o LSI MegaRAID SAS 8408E o LSI MegaRAID SAS 8480E o LSI MegaRAID SAS 9260 o Dell PERC5 o Dell PERC6 o IBM ServeRAID M5015 SAS/SATA o IBM ServeRAID-MR10i o Intel RAID Controller SROMBSAS18E FILES
/dev/mfid? array/logical disk interface /dev/mfi? management interface DIAGNOSTICS
mfid%d: Unable to delete busy device An attempt was made to remove a mounted volume. SEE ALSO
amr(4), pci(4), mfiutil(8) HISTORY
The mfi driver first appeared in FreeBSD 6.1. AUTHORS
The mfi driver and this manual page were written by Scott Long <scottl@FreeBSD.org>. BUGS
The driver does not support big-endian architectures at this time. BSD
May 12, 2010 BSD
All times are GMT -4. The time now is 10:17 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy