04-07-2009
red hat 4 core off or on
Hi All,
I have this IBM 8872-1RU/X460
I need to know if the cpu core is off or on.
Is there a query to do that without checking the BIOS?
Here's the cpuinfo
~~~~~~~~~~~~~~~~~~~~
[root@localhost ~]# cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Xeon(TM) CPU 3.00GHz
stepping : 8
cpu MHz : 3002.706
cache size : 2048 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall lm pni monitor ds_cpl est tm2 cid cx16 xtpr lahf_lm
bogomips : 6014.45
clflush size : 64
cache_alignment : 128
address sizes : 40 bits physical, 48 bits virtual
power management:
~~~~~~~~~~~~~~~~~~~~
Thanks for any comment you may add.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just installed red hat 7.2 on my laptop. it's dual booted with xp and red hat. when i boot in to linux it boots up to the screen to ask me my name and pass....i put in root and my password. after this it goes to a blue screen and sits there. the after about 2 minutes it comes up with a fatal... (1 Reply)
Discussion started by: muzscman
1 Replies
2. Linux
I have a Red Hat upgrade disk. I installed it and it corrupted my entire hard drive! I had gotten the disks out of a Dummy's book at my local library. Trying to install 'Red Hat', has cost me $100.00 in damages. (The cool part is my friend gave me that $100.00 part) Ah...A 120gig Hard Drive. Just... (3 Replies)
Discussion started by: hdk_mkr
3 Replies
3. UNIX for Dummies Questions & Answers
please help me how to install softwares in linux.i have a ethernet internet connection.i try to open the site on LAN to download internet client.but i cannot as our lan supports only internet explorer....i downloaded the linux client by booting thru XP......but i cannot c my NTFS partition thru... (0 Replies)
Discussion started by: shobhit143
0 Replies
4. Linux
Hello, I have a Red Hat As 2.1 server and need to make a backup of the entire system, something similar to AIX's mksysb or HP-UX's Ignite, in case configuration changes that need to be made fail. Is this possible with RH AS 2.1? If so, how would this be accomplished? (1 Reply)
Discussion started by: zuessh
1 Replies
5. Linux
hello.
I would be greatfull if someone could tell me how will i see what dns server and gateway my red hat server uses.
I tryied to find out by typing ifconfig command but i got :
-bash: ifconfig: command not found , although man ifonconfig gives output with info about using that command.
Is... (3 Replies)
Discussion started by: tonijel
3 Replies
6. Red Hat
I'm am working with a Red Hat Enterprise 3 server.
This is a dedicated server that is supposedly dedicated to one domain, but I have been tasked with trying to figure out if there are files on this system that are being accessed by other IP's.
Does anyone know if how I would go about finding... (0 Replies)
Discussion started by: chrisPlusPlus
0 Replies
7. Red Hat
Hello,
How do I see what IP addresses are connected to my machine?
thanks (2 Replies)
Discussion started by: sonomao
2 Replies
8. UNIX for Dummies Questions & Answers
how to know if i use "Red Hat Enterprise Linux" or "Red Hat Desktop" ? (2 Replies)
Discussion started by: ahmedamer12
2 Replies
9. Red Hat
Hello All,
I am new joiner of this forum.I am new to Linux shell scripting.
At present I have identified 1 application which stalls very frequently (PID is say xyz) and I am not having much information in its application log to identify the root cause of stalling. I need to take the core dump... (19 Replies)
Discussion started by: Anjan Ganguly
19 Replies
CPUID(4) Linux Programmer's Manual CPUID(4)
NAME
cpuid - x86 CPUID access device
DESCRIPTION
CPUID provides an interface for querying information about the x86 CPU.
This device is accessed by lseek(2) or pread(2) to the appropriate CPUID level and reading in chunks of 16 bytes. A larger read size means
multiple reads of consecutive levels.
The lower 32 bits of the file position is used as the incoming %eax, and the upper 32 bits of the file position as the incoming %ecx, the
latter intended for "counting" eax levels like eax=4.
This driver uses /dev/cpu/CPUNUM/cpuid, where CPUNUM is the minor number, and on an SMP box will direct the access to CPU CPUNUM as listed
in /proc/cpuinfo.
This file is protected so that it can only be read by the user root, or members of the group root.
NOTES
The CPUID instruction can be directly executed by a program using inline assembler. However this device allows convenient access to all
CPUs without changing process affinity.
Most of the information in cpuid is reported by the kernel in cooked form either in /proc/cpuinfo or through subdirectories in
/sys/devices/system/cpu. Direct CPUID access through this device should only be used in exceptional cases.
The cpuid driver is not auto-loaded. On modular kernels you might need to use the following command to load it explicitly before use:
$ modprobe cpuid
There is no support for CPUID functions that require additional input registers.
Very old x86 CPUs don't support CPUID.
SEE ALSO
Intel Corporation, Intel 64 and IA-32 Architectures Software Developer's Manual Volume 2A: Instruction Set Reference, A-M, 3-180 CPUID ref-
erence.
Intel Corporation, Intel Processor Identification and the CPUID Instruction, Application note 485.
COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 2009-03-31 CPUID(4)