04-06-2009
1. If you hard set the switch to 1000 then you would have to do the same to the network interface, .i.e. both ends have to autoneg or neither end should.
2. Setting the switch or the port to only advertise 1000, FD, while still using autoneg should be okay.
Sounds like the switch or network cable are not 1000 capable?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I see you guys encouraged people studied and used C while they were working on UNIX. Does C++ or JAVA matter? And in the past threads, Neo, PxT, and other members recommanded lots good books. I think those people who asked for the references, such as Dominic, had experiences on sys admin or... (8 Replies)
Discussion started by: HOUSCOUS
8 Replies
2. IP Networking
I am trying to set an interface to 100/Full, but the command I use are getting rejected. I think it is the last argument, but I don't know how to find the correct values.
I am trying to use the following script, but change hme to le .
echo "Setting hme interface 1: 100mb/full-duplex..."
... (2 Replies)
Discussion started by: bbrandeb49
2 Replies
3. UNIX for Advanced & Expert Users
My question is: difference between unix and linux in terms of compiler, file system, ANSI
compliance, standard liabrary issues, threading issues, operating system
calls memory issues..ie whether these things wud cause problems while
porting a unix programme to linux.?
I think answer is depend... (1 Reply)
Discussion started by: prasoon
1 Replies
4. Solaris
Hi Guys,
I need help with ndd.
I was going through network FAQ but i have more questions then answers regarding ndd.
#ndd -set /dev/hme instance 0
#ndd -set /dev/hme adv_100fdx_cap 1
#ndd -set /dev/hme adv_100hdx_cap 0
#ndd -set /dev/hme adv_10fdx_cap 0
#ndd -set /dev/hme adv_10hdx_cap 0... (2 Replies)
Discussion started by: nitinkgoud
2 Replies
5. Solaris
Hello Gurus
I would like to know more about ndd commands related to ethernet(NIC) like how to set link_status, link_speed & link_mode as I know how to check these value. And I also would like to know how to make these setting permanents after reboot as I know that these setting will vanish... (5 Replies)
Discussion started by: amity
5 Replies
6. Programming
Hi,
Is there any function calls available ( for using in a C program ) to get the Ethernet Link status. ?
I am looking for the status available from
ndd /dev/hme link_status
And how about plumbing and configuring an interface using C program ?
BTW, Is all this documented... (3 Replies)
Discussion started by: shibz
3 Replies
7. Solaris
Solaris 10 server (SunOS 5.10 Generic_137137_09)
I have a services file configured in /etc in there windows clients connect to my server on port 6034-6037
when I do the following
netstat | grep TestServices
it pulls all the connections active for those ports
so right now I have 10 clients... (3 Replies)
Discussion started by: deaconf19
3 Replies
8. UNIX for Advanced & Expert Users
I have a T2000 server which has 4 e1000g NIC cards
How do I configure each of it for 1Gbit full duplex and turnoff autonegotiation.
Please assist
Thanks (4 Replies)
Discussion started by: Tirmazi
4 Replies
9. Solaris
Hello forum,
I have a Solaris 9 Sun Fire v240 server and Sun Fire v440
Recently we made changes and installed a new switch which both of them are connected to it. Cisco Catalyst 3750.
Now the Sun Server v240 is having problems with the network. It was supposed to run at 1000mbs speed.
ndd... (10 Replies)
Discussion started by: br1an
10 Replies