interface ce1 up-down Post: 302304262

9 More Discussions You Might Find Interesting

1. Solaris

ce0 and ce1 have the same mac address

i have ce0 and ce1 online, on 2 different networks. im getting a message that says one nic is trying to assume the others IP or something to thta effect. I do ifconfig -a and i see they have the same mac. How do i deal with this? Solaris 9 i beleive 04/04 Thanks, Brian

2. Solaris

interface may off

Dear ALL, my server give me messages like below: Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off I check with ifconfig,but nothing error that,how can make it solve...thanks for your help.

3. Solaris

SunFire V440 Quad gigabit ce1 won't run Gig

Hi there. My first time posting so apologies for any indescretions in advance. :o I've got two SunFire V440 servers running Solaris 5v10. Both have a quad Gigabit ethernet card fitted, both have the same symptom; that is, I can't get the first port ce1 to run Gigabit. Motherboard ports are ce0 and...

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

5. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

6. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

7. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance.

8. UNIX for Dummies Questions & Answers

Solaris Logic to transmit traffic to physical interfaces ( eg ce0 and ce1)

Just wanted to understand what is the logic being used by Solaris(kernel) to transmit data/traffic on physical interfaces. I have seen most of the time traffic is being sent to interface ce0 and sometime to ce1. I have removed ip address from below command for some reason. netstat -rn ...

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT SUNOS

liebert

LIEBERT(8)							    NUT Manual								LIEBERT(8)

NAME

       liebert - Driver for Liebert contact-closure UPS equipment

NOTE

       This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).

SUPPORTED HARDWARE

       This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
       contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.

EXTRA ARGUMENTS

       This driver does not support any extra settings in the ups.conf(5).

BUGS

       This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
       You may have to build another cable with DTR connected through to the UPS for it to work.

       There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
       fundamental limitation of any contact-closure driver.

SEE ALSO

   The core driver:
       nutupsdrv(8)

   Internet resources:
       The NUT (Network UPS Tools) home page: http://www.networkupstools.org/

Network UPS Tools						    05/21/2012								LIEBERT(8)