04-06-2009
I'm not entirely sure that its due to a faulty cable. You might get similar errors if you have any commands that change the speed of the interface (ndd set or something like that). Not sure that there should be a 2 second gap between the interface going down and coming back up, but its possible.
9 More Discussions You Might Find Interesting
1. Solaris
i have ce0 and ce1 online, on 2 different networks. im getting a message that says one nic is trying to assume the others IP or something to thta effect.
I do ifconfig -a and i see they have the same mac.
How do i deal with this?
Solaris 9 i beleive 04/04
Thanks,
Brian (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
2. Solaris
Dear ALL,
my server give me messages like below:
Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off
I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Discussion started by: fredginting
7 Replies
3. Solaris
Hi there. My first time posting so apologies for any indescretions in advance. :o I've got two SunFire V440 servers running Solaris 5v10. Both have a quad Gigabit ethernet card fitted, both have the same symptom; that is, I can't get the first port ce1 to run Gigabit. Motherboard ports are ce0 and... (10 Replies)
Discussion started by: fixit9660
10 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies
8. UNIX for Dummies Questions & Answers
Just wanted to understand what is the logic being used by Solaris(kernel) to transmit data/traffic on physical interfaces.
I have seen most of the time traffic is being sent to interface ce0 and sometime to ce1.
I have removed ip address from below command for some reason.
netstat -rn
... (3 Replies)
Discussion started by: nadeemahmed
3 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT SUNOS
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)