04-05-2009
Hi,
we are doing this via 3DNS - the clusters are configured on both sides to connect to the 3DNS IP adress that fails over automatically to the DR site as soon as the PROD site is down.
Works perfectly fine.
Rgds
zxmaus
10 More Discussions You Might Find Interesting
1. High Performance Computing
Hello,
This might not be the right place to post my questions.
- I installed VCS 5.0 on the 2 nodes. What's next? I want to test the HA of NFS: i.e. the shared disk always accessible if one node goes down. How to do that?
- The management console was not installed. This is the GUI to manage... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies
2. Solaris
Is it possible to configure veritas cluster server using 2 Ldoms on same host? I just want to test and learn VCS. We can do a cluster (sun cluster3.2 ) in a box using 2 Ldoms but i 'm not sure if thats possible with veritas cluster or not ? (1 Reply)
Discussion started by: fugitive
1 Replies
3. Solaris
Hi,
We have two sun SPARC server in Clustered (Sun Cluster 3.1). For some reason, System 1 failed over to System 2. Where can I find the logs which could tell me the reason for this failover?
Thanks (5 Replies)
Discussion started by: Mack1982
5 Replies
4. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
5. Gentoo
How to failover the cluster ? GNU/Linux
By which command,
My Linux version
2008 x86_64 x86_64 x86_64 GNU/Linux
What are the prerequisites we need to take while failover ?
if any
Regards (3 Replies)
Discussion started by: sidharthmellam
3 Replies
6. UNIX for Advanced & Expert Users
Hello,
Usually I use "vxresize" to grow vxfs directory in a stand-alone server without any problems, but I am just told to grow vxfs directorys in Veritas Cluster nodes.
Since I never done it before, would like to ask all the experts here to make sure the concept and steps will be fine... (1 Reply)
Discussion started by: sunnychen98
1 Replies
7. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
8. Solaris
Until I really began to explore the practical implications of using ZFS with VCS, I would not have necessarily realised the obstacles that would be put in my path. Data integrity is a must-have for storage in a shared host environment, so it surprised me to learn as I opened this particular... (0 Replies)
Discussion started by: cambridge
0 Replies
9. Red Hat
Hi Guys,
I am not much aware of clusters but i have few questions can someone provide the overview as it would be very helpful for me.
How can i perform cluster failover test to see all the services are failing back to other node ? If it is using veritas cluster then what kind of... (2 Replies)
Discussion started by: munna529
2 Replies
10. UNIX for Beginners Questions & Answers
Hi Experts,
I wanted to extend a veritas file system which is running on veritas cluster and mounted on node2 system.
#hastatus -sum
-- System State Frozen
A node1 running 0
A node2 running 0
-- Group State
-- Group System Probed ... (1 Reply)
Discussion started by: Skmanojkum
1 Replies
hpsmh(1M) hpsmh(1M)
NAME
hpsmh - starts or stops the HP System Management Homepage server
SYNOPSIS
DESCRIPTION
The HP System Management Homepage is the management server for web-based System Administration tools. In order to use HPSMH, start a web
browser on your desktop or workstation, and type in the URL or Address of the server to be managed:
By default, the HP SMH management server under HP-UX only starts on demand. It does not run continually. A daemon listens on port 2301 to
start an instance of the management server. The above URL automatically starts the management server, then redirects your browser to the
secure port from which to login:
The command starts or stops the HPSMH server. If no options are specified, displays the possible options.
Options
The command supports the followings options:
Starts the HPSMH Server if is not currently running
Stops the HPSMH Server
Access Control
By default, only the root user can login to HPSMH. Within HPSMH you can configure additional user groups to have HPSMH access.
You must be a superuser to run the command.
Certificates
Installing HPSMH will generate an SSL self signed certificate. Because this certificate is self signed, when connecting to HPSMH your web
browser will prompt you with a warning that the certificate was issued by a web site, company or Certificate Authority you have not chosen
to trust.
It is possible to proceed by accepting this self signed certificate temporarily for each session. You can also view and install (accept
permanently) this certificate to avoid this warning in the future. HPSMH also supports installation of certificates created by a Certifi-
cate Authority.
RETURN VALUES
The command returns:
upon successful completion
if the command failed
EXAMPLES
Starts HPSMH Server:
Stops HPSMH Server:
Shows options:
Using HPSMH, start a browser and enter the following URL:
AUTHORS
was developed by Hewlett-Packard
SEE ALSO
smhstartconfig(1M).
hpsmh(1M)