04-05-2009
Hi,
we are doing this via 3DNS - the clusters are configured on both sides to connect to the 3DNS IP adress that fails over automatically to the DR site as soon as the PROD site is down.
Works perfectly fine.
Rgds
zxmaus
10 More Discussions You Might Find Interesting
1. High Performance Computing
Hello,
This might not be the right place to post my questions.
- I installed VCS 5.0 on the 2 nodes. What's next? I want to test the HA of NFS: i.e. the shared disk always accessible if one node goes down. How to do that?
- The management console was not installed. This is the GUI to manage... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies
2. Solaris
Is it possible to configure veritas cluster server using 2 Ldoms on same host? I just want to test and learn VCS. We can do a cluster (sun cluster3.2 ) in a box using 2 Ldoms but i 'm not sure if thats possible with veritas cluster or not ? (1 Reply)
Discussion started by: fugitive
1 Replies
3. Solaris
Hi,
We have two sun SPARC server in Clustered (Sun Cluster 3.1). For some reason, System 1 failed over to System 2. Where can I find the logs which could tell me the reason for this failover?
Thanks (5 Replies)
Discussion started by: Mack1982
5 Replies
4. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
5. Gentoo
How to failover the cluster ? GNU/Linux
By which command,
My Linux version
2008 x86_64 x86_64 x86_64 GNU/Linux
What are the prerequisites we need to take while failover ?
if any
Regards (3 Replies)
Discussion started by: sidharthmellam
3 Replies
6. UNIX for Advanced & Expert Users
Hello,
Usually I use "vxresize" to grow vxfs directory in a stand-alone server without any problems, but I am just told to grow vxfs directorys in Veritas Cluster nodes.
Since I never done it before, would like to ask all the experts here to make sure the concept and steps will be fine... (1 Reply)
Discussion started by: sunnychen98
1 Replies
7. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
8. Solaris
Until I really began to explore the practical implications of using ZFS with VCS, I would not have necessarily realised the obstacles that would be put in my path. Data integrity is a must-have for storage in a shared host environment, so it surprised me to learn as I opened this particular... (0 Replies)
Discussion started by: cambridge
0 Replies
9. Red Hat
Hi Guys,
I am not much aware of clusters but i have few questions can someone provide the overview as it would be very helpful for me.
How can i perform cluster failover test to see all the services are failing back to other node ? If it is using veritas cluster then what kind of... (2 Replies)
Discussion started by: munna529
2 Replies
10. UNIX for Beginners Questions & Answers
Hi Experts,
I wanted to extend a veritas file system which is running on veritas cluster and mounted on node2 system.
#hastatus -sum
-- System State Frozen
A node1 running 0
A node2 running 0
-- Group State
-- Group System Probed ... (1 Reply)
Discussion started by: Skmanojkum
1 Replies
LEARN ABOUT LINUX
a2ensite
A2ENSITE(8) System Manager's Manual A2ENSITE(8)
NAME
a2ensite, a2dissite - enable or disable an apache2 site / virtual host
SYNOPSIS
a2ensite [site]
a2dissite [site]
DESCRIPTION
This manual page documents briefly the a2ensite and a2dissite commands.
a2ensite is a script that enables the specified site (which contains a <VirtualHost> block) within the apache2 configuration. It does this
by creating symlinks within /etc/apache2/sites-enabled. Likewise, a2dissite disables a site by removing those symlinks. It is not an
error to enable a site which is already enabled, or to disable one which is already disabled.
The default site is handled specially: The resulting symlink will be called 000-default in order to be loaded first.
EXAMPLES
a2dissite default
Disables the default site.
FILES
/etc/apache2/sites-available
Directory with files giving information on available sites.
/etc/apache2/sites-enabled
Directory with links to the files in sites-available for enabled sites.
SEE ALSO
apache2ctl(8).
AUTHOR
This manual page was written by Stefan Fritsch <sf@debian.org> (based on the a2enmod manual page by Daniel Stone <daniel@sfarc.net>) for
the Debian GNU/Linux distribution.
8 June 2007 A2ENSITE(8)