If you really do want a monitor attached to your 280 then you will need to install a Sun graphics card, e.g. XVR-100 this comes with a VGA connector although the default resolution is 1152x900 which many monitors do not like so when you set the output-device in the OBP you will also need to set a more standard resolution, e.g.:
As DukeNuke2 mentioned you may want to get some ear plugs as well!
Hello all,
I'm lost and can't figure this problem out.
I have a Sun fire 280R running Solaris 8. Everything was working great. I have one drive in bay 1(not 0). But when I reboot the system it trys to open files in /dev/rdsk/c1t1d0s0. Should it have been opeing /dev/rdsk/c1t0d0s0, the... (4 Replies)
All,
After a power loss I went to power on our sun fire v120 that is running solaris 10 and now it will not boot. I tried power cycling it from the lom and pulling the cord but nothing works. All it does is after a power cycle it will start to boot and then start to spit out a bunch of hex... (2 Replies)
Hello there!
I have Sun Fire 3800 with very old Solaris 9 and I need to perform upgrade to concurrent Solaris 10 version, preserving current OS configuration. I supose to make it using Live Upgrade, but according to Solaris Live Upgrade Software: Minimum Patch Requirements page, I need to... (5 Replies)
Hi:
I bougth an used Sun Fire v440, and It have a firmware password. When I turn on the server, it ask for firmware password. (I don 't know what is the correct password). I can access to SC, but when I want to access to OBP, Firmware Password appears again. I remove the battery for two hours,... (1 Reply)
Hi ,
during 2 weeks i´ve been trying to find them.
i need DCMU packets for managing internal disks on sun fire x4500 and sun fire x4600 on rhel. i have opened to tickets to myoraclesupport but no answer.
please anybody could tell me a link or anythiing?? i´ve been searching and searching... (1 Reply)
:)Dear Solaris Experts,
I need to clone a Solaris 10 x86 system using a ufsdump backup from the following source & target servers:
Sun Fire x2200 M2 with Quad Core Processor
# /usr/platform/`uname -i`/sbin/prtdiag
System Configuration: Sun Microsystems Sun Fire X2200 M2 with Quad Core... (8 Replies)
Hi,
I have a SUN Fire V440 server running Solaris 8. One of the 4 disks do not appear when issued the format command. The "ready to remove" LED is not on either.
Metastat command warns that this disk "Needs maintenace". Can I just shutdown and power off the machine and then insert an... (5 Replies)
Hey Guys I am new here, dont know if any one can assist me with this issue.
I have a Sun-Fire-V490 machine that was upgraded to version 9 and patched a few months back.
Problem is a few network printers managed by the server is printing an extra page that comes out before and after every print... (0 Replies)
cat note
Hi Sun Solaris Experts,
When I try to install Solaris 8 10/00 OS via the Solaris 8 Installation Disk on our Sun Fire V490 Server using the command , I get:
boot: cannot open kernel/sparcv9/unix
which means it can't find the unix kernel file on the installation disk .
By the way, I... (5 Replies)
Hi Solaris/Unix Experts,
I've installed Oracle Solaris 10 1/13 on a Sun Fire V490 Server via its external Serial Port using a Cisco Console Cable connected to my Laptop PC running SecureCRT terminal emulation software emulating VT100 Terminal.
The Sun Fire V490 server has two on-board... (1 Reply)
Discussion started by: ssabet
1 Replies
LEARN ABOUT DEBIAN
snmp::info::layer3::sun
Info::Layer3::Sun(3pm) User Contributed Perl Documentation Info::Layer3::Sun(3pm)NAME
SNMP::Info::Layer3::Sun - SNMP Interface to L3 Sun Solaris
AUTHOR
begemot
SYNOPSIS
# Let SNMP::Info determine the correct subclass for you.
my $sun = new SNMP::Info(
AutoSpecify => 1,
Debug => 1,
DestHost => 'mysunrouter',
Community => 'public',
Version => 1
)
or die "Can't connect to DestHost.
";
my $class = $sun->class();
print "SNMP::Info determined this device to fall under subclass : $class
";
DESCRIPTION
Subclass for Generic Sun Routers running SunOS
Inherited Classes
SNMP::Info::Layer3
Required MIBs
Inherited Classes' MIBs
See "Required MIBs" in SNMP::Info::Layer3 for its own MIB requirements.
GLOBALS
These are methods that return scalar value from SNMP
$sun->vendor()
Returns 'sun'
$sun->os()
Returns 'sun'
$sun->os_ver()
Returns the software version extracted from message of the day.
$sun->model()
Returns 'Solaris Router'
$sun->serial()
Returns serial number
Globals imported from SNMP::Info::Layer3
See documentation in "GLOBALS" in SNMP::Info::Layer3 for details.
TABLE METHODS
These are methods that return tables of information in the form of a reference to a hash.
Overrides
$sun->i_ignore()
Returns reference to hash. Increments value of IID if port is to be ignored.
Ignores loopback
Table Methods imported from SNMP::Info::Layer3
See documentation in "TABLE METHODS" in SNMP::Info::Layer3 for details.
perl v5.12.4 2011-09-28 Info::Layer3::Sun(3pm)